background image

47

6 Set up the sensor with the display and adjustment module

VEGAPULS 69 • Modbus and Levelmaster protocol

47252-EN-210205

In this menu item you can define the way measured values are indi

-

cated on the display.

The default setting for the display value is " 

Percent

". 

The display and adjustment module has a backlight for the display. In 

this menu item you can switch the lighting on or off. You can find the 

required operating voltage in chapter " 

Technical data

". 

To maintain the function of the device, the lighting is temporarily 

switched off if the power supply is insufficient.

In delivery status, the lighting is switched on.

In this menu item, the device status is displayed.

The min. and max. measured value, the measurement reliability as 

well as the min. and max. electronics temperature are stored in the 

sensor. The values are displayed in menu item " 

Peak value

" or " 

Further peak values

". 

A reset menu is opened with the 

[OK]

 key in the respective peak 

value window: 

With the 

[OK]

 key in the reset menu, the peak values are reset to the 

current measured value. 

The " 

Echo curve

" shows the signal strength of the echoes over the 

measuring range in dB. The signal strength enables an evaluation of 

the quality of the measurement. 

The selected curve is continuously updated. A submenu with zoom 

functions is opened with the 

[OK]

 key: 

Display - Displayed value 

1 and 2

Display - Backlight

Diagnostics - Device 

status

Diagnosis - Peak value

Diagnosis - Curve indica-

tion

Содержание VEGAPULS 69





































































































Отзывы: