Vega VEGAPULS 69 Скачать руководство пользователя страница 30

Страница: 30 / 100

4 Mounting

VEGAPULS 69 • Modbus and Levelmaster protocol

47252-EN-210205

Fig. 26: Installation and orientation in multiple chamber silos

To avoid heavy buildup and dust on the antenna, the device should

not be mounted close to the dust exhauster inside the vessel.
To protect the device against buildup, particularly in case of strong

condensation, air rinsing is recommended.

Flange with lens antenna

The VEGAPULS 69 with metal-jacketed lens antenna is equipped

with a rinsing air connection as a standard feature, see following

graphics.

Fig. 27: Rinsing air connection on metal-jacketed lens antenna

Plastic horn antenna

The VEGAPULS 69 with plastic horn antenna is optionally available

with a rinsing air connection. The mechanical configuration differs

according to the flange version, see following graphics.

Dust deposits - Rinsing

air connection

Содержание VEGAPULS 69





































































































Результаты поиска

Содержание VEGAPULS 69

Отзывы:

Похожие инструкции для VEGAPULS 69

Бренды по названию

Популярные бренды

Vega VEGAPULS 69, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 69

Отзывы:

Похожие инструкции для VEGAPULS 69

Бренды по названию

Популярные бренды