background image

5

1 For your safety

VEGAPULS 62 • 4 … 20 mA/HART - four-wire

47121-EN-160215

• 

The mounting location must be at least 4 km away from radio 

astronomy stations, unless special permission was granted by the 

responsible national approval authority

• 

When installed within 4 to 40 km of a radio astronomy station, 

the instrument must not be mounted higher than 15 m above the 

ground.

You can find a list of the respective radio astronomy stations in chap

-

ter "

Supplement

".

1.8  Radio license for USA/Canada

The instrument is in conformity with part 15 of the FCC regulations. 

Take note of the following two regulations:

• 

This device may not cause interference, and

• 

The device must be resistant to interference signals, including 

such that may cause undesired operating states of the device

Modifications not expressly approved by the manufacturer will lead to 

expiry of the operating licence according to FCC/IC.

The instrument is in conformity with RSS-210 of the IC regulations.
The instrument may only be used in closed vessels made of metal, 

concrete, or fibre-reinforced plastic.

1.9  Environmental instructions

Protection of the environment is one of our most important duties. 

That is why we have introduced an environment management system 

with the goal of continuously improving company environmental pro-

tection. The environment management system is certified according 

to DIN EN ISO 14001.

Please help us fulfill this obligation by observing the environmental 

instructions in this manual:

• 

Chapter "

Packaging, transport and storage

"

• 

Chapter "

Disposal

"

Содержание VEGAPULS 62





















Отзывы: