VeEX UX400 Скачать руководство пользователя страница 84

Страница: 84 / 209

Summary:

The Summary tab displays the status of each service and test as Pass, Failed, Pending, or Disabled.

Results - Config. Tests - Summary

Go back to top

Go back to TOC

6.4.2.2 Performance Test

The

Service #

tabs display min, mean, and max values for

IR Mbps

FTD

FDV

Frame Loss Count

Frame Loss Ratio (%)

Availability

, and

Errored Frame Count

Pass/Fail/Pending status of each test is displayed on the top of each table.

IR Mbps

FTD

FDV

Frame Loss Count

Frame Loss Ratio (%)

definitions are listed in the

Configuration Test

section.

Availability:

Minimum percentage of service availability allowed to still be compliant with the SLA. The service becomes unavailable if more than 50% of the

frames are errored or missing in a one second interval. Availability is only guaranteed for traffic conforming to the CIR.

Total RX Frames:

Total number of frames received

Errored Frame Count:

Number of frames with CRC or IP Checksum errors

Measured values that do not meet the service test parameters set in the Bandwidth and Threshold tabs cause the test to fail.

Perf. Test - Service 1

The

Summary

tab displays the status of each service and test as

Pass

Failed

Pending

, or

Disabled

Perf. Tests - Summary

UX400 10G e-Manual D07-00-058P RevA00

Page 84 of 209

Содержание UX400


















































































































































































































Результаты поиска

Содержание UX400

Отзывы:

Похожие инструкции для UX400

Бренды по названию

Популярные бренды

VeEX UX400, Руководство пользователя

Результаты поиска

Содержание UX400

Отзывы:

Похожие инструкции для UX400

Бренды по названию

Популярные бренды