VeEX UX400 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 209

background image

Tap the

Laser On/Off

button on the right side of the screen.

The Laser On/Off button will turn Red, while the soft LEDs for Signal and Frame will start blinking.

Tap the

History

button displayed below the soft LEDs. The LEDs will now turn steady green and the test tab will also turn green, indicating the module is ready to perform

different tests.

Ready for Testing Tasks

10GE Test App Home Screen (Dual Port)

Ethernet Dual Port Operation

When the dual port interfaces and software options are enabled, the test module can operate a combination of two ports at the same time.

Note:

The configuration parameters (header, bandwidth, etc.) for each application (on each of the ports) are completely independent from one another. All test feature

combinations are allowed and completely independent (Loopback, BERT, Throughput, RFC2544, V-SAM) in dual port operation. However, some advanced tools like VoIP,
IPTV, VLAN scan, Packet Capture are only available in single port testing mode. The User Interface will provide an error message when a feature is not available in dual
port operation.

Start All:

The Start All button is located on the right side of the dual port operation mode screen. Tapping this button will simultaneously start a test on both

ports.

Stop All:

Once the test starts on both ports, the Start All button will change to Stop All. Tapping on this button will simultaneously stop the test on both ports.

6.1 Setup

6.1.1 Port Setup

Port setup configuration is accessed from the Setup menu located on the home page of 10GE Test App.

UX400 10G Ethernet Test App Setup

UX400 10G e-Manual D07-00-058P RevA00

Page 35 of 209

«
...
33
34
35
36
37
...
»

Содержание UX400


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UX400

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Lamtec Страницы: 22

Бренд: Union Instruments Страницы: 63

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 140

Бренд: MaintTech Страницы: 28

Бренд: HQ Power Страницы: 23

Бренд: Westfalia Страницы: 18

ArmorBlock 1732E-16CFGM12R

Бренд: Allen-Bradley Страницы: 20

Бренд: Integral Страницы: 7

Бренд: select solar Страницы: 2

Бренд: Conel Страницы: 52

Бренд: Revox Страницы: 57

Бренд: Wittenstein Страницы: 52

Бренд: ACTi Страницы: 20

Бренд: SOARNEX Страницы: 14

Бренд: Tristan Auron Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды