background image

Operation

Viewing PMC Reports Via RS-232 Connection

a. Go to the console front panel press the MODE key until you see:

b. Press the FUNCTION key until you see the message:

c. Press the STEP key until you see the message: 

d. Press the PRINT key to printout the port settings for all communication modules installed in the console. 

Figure 11 shows an example port settings printout with the RS-232 module installed. Using the console 
port settings in the example below, your HyperTerminal ‘Port Settings’ window entries would be Bits per 
second - 2400, Data bits - 7, Parity - None, Stop Bits - 1. For the ‘Flow Control’ entry select None. Click 
OK.

Figure 11.  Console comm port settings printout example

In the example port settings printout above, the RS-232 Security Code is disabled. If the code was enabled you 
would see a 6-digit number which you will need to enter to access the console (refer to the ‘Sending Console 
Commands’ paragraph below for more information).

 SETUP MODE

PRESS <FUNCTION> TO CONT

COMMUNICATIONS SETUP

PRESS <STEP> TO CONTINUE

PORT SETTINGS
PRESS <ENTER>

PORT 

S

ETTING

S

COMM BOARD: 1 (R

S

-

2

3

2

)

BAUD RATE: 

2

400

PARITY: ODD

S

TOP BIT: 1 

S

TOP

DATA LENGTH: 1 DATA

R

S

-

2

3

2

 

S

ECURITY

CODE: DI

S

ABLED

isd\portset.eps

This number is the assigned by the console and indicates the slot 
in which the RS-232 module is installed. It could be 1, 2, or 3.
However, for the RS-232 port of a Multiport module, which is installed
in slot 4, this number would be 6.  

If no RS-232 Security Code has been entered, you will see disabled.
If a code has been entered, e.g., 000016, that 6-digit number would 
appear here.  If a code appears, you will need to enter this code with 
each command you send to the console.

Section 16

Pressure Management Control

16-13

Содержание TLS-350R

























Отзывы: