background image

Setup

PMC Setup

PMC Setup

Figure 3 diagrams the PMC setup programming.

Figure 3.  PMC Setup

PMC SETUP
PRESS <STEP> TO CONTINUE

SETUP MODE

PRESS <FUNCTION> TO CONT

VAPOR PROCESSOR
MAX RUNTIME MINUTES:  60

Prints out a copy of the 
PMC Setup entries. See
example at right.

M

P

S

S

F

TURN OFF VAPOR PROCESSOR
INCHES WC: -0.200

Range checking is enforced:
2<minutes <= 180 
Default: 60 minutes

 

S

TURN ON VAPOR PROCESSOR
INCHES WC: +0.200

S

HYDROCARBON SELECT 
PRESS <ENTER>

Use <ENTER> key to make selection 
MODBUS Sensor default enabled

S

OVER PRESSURE LIMIT
INCHES WC:  xx.xx

Range checking is enforced:
0 < xx.xx < 3.5
Default: 0.0

S

DUTY CYCLE LIMIT
xx.xx %

Range checking is enforced:
0 < xx.xx < 100
Default: 75%

Use <CHANGE> key to enter.
Default Start time = 11:59 PM

Use <CHANGE> key to enter.
0< delay < =720
Default:= 001

NOTE: If delay minutes =0, the results will be posted as soon as 
they become available, else mmm minutes after start time.

Data collected 5 minutes before the Start of Test time is omitted 
from test.

S

SET ANALYSIS TIME 
PRESS <ENTER>

E

S

SET TEST START TIME
TIME:  hh:mm

SET POST DELAY DURATION
DELAY MINUTES:  mmm

isd\pmc-1.eps

C

F

P

S

T

Change

E

Enter

Function

Print

M

Mode

Step

Tank/Sensor

Key press
sequence

Repress until
desired message
appears in display

Key Legend

1

2

PMC SETUP

---------------------- 

PMC VERSION: 01.00

VAPOR PROCESSOR TYPE  

VST VAPOR PROCESSOR

MAX RUNTIME MINUTES: 90

ON: -0.200 INCHES

OFF:-0.600 INCHES

EFFLUENT EMISSIONS LIMIT

0.649 LB/1KG 

OVER PRESSURE LIMIT

xx.xx PERCENT% 

 

DUTY CYCLE LIMIT

xx.xx PRECENT%

ANALYSIS TIMES

TIME 11:59 PM

DELAY MINUTES 1

 

+3

0

+0.2

Turn On 

vapor processor

Ullage vapor pressure

Turn Off 

vapor processor

-0.2 

-8

Absolute

Range

(IWC)

P/V valve opens

Vapor Processor 
On/Off example

Sets vapor processor Off point. Range: 
-8 < Off setting < On setting. For more 
information see example at right. 

Sets vapor processor On point. Range: 
Off setting < On setting < +3. For more 
information see example at right. 

NOTE: This menu is not used.

Section 16

Pressure Management Control

16-6

Содержание TLS-350R

























Отзывы: