background image

Displayed Alarm Messages

2

Displayed Alarm Messages

Common Alarm messages and a possible cause/action for the Alarms are listed in the table below. Actual Alarms 
displayed by a particular console will depend upon the features installed. 

Short Device IDs used in the table below:

C = 2-wire CL sensor

Co = Comm device

G = Groundwater sensor

H = 3-wire CL sensor

I = External input

L = Liquid sensor

MS = Mag sensor

P = Printer

Pm = Pump

Q = PLLD line

R = Relay 

(TLS4/TLS-450PLUS), 

R = Receiver 

(TLS-3XX)

T = Tank

s = Smart sensor

V = Vapor sensor

Messa

g

e

Short 

Device ID

Cause

Action

Annual Test Needed Alarm

Q, T

System failed to perform an annual test (0.1 gph 
[0.38 lph]) in the programmed number of days.

Schedule a 0.1 gph (0.38 lph) test.

Annual Test Needed Warn-
ing

Q, T

System failed to perform an annual test (0.1 gph 
[0.38 lph]) in the programmed number of days.

Schedule a 0.1 gph (0.38 lph) test.

Annual Line Test Fail 
Alarm

Q

0.1 gph (0.38 lph) line test failure. Dispensing 
halts, if programmed to do so.

Consult PLLD Alarm Quick Help Guide and 
PLLD diagnostic screens.

Annual Leak Test Fail 
Alarm

T

System failed an annual in-tank leak test.

Rerun in-tank leak test. If second test fails, 
call for service.

Autodial Failed Alarm

(TLS4/TLS-450PLUS only)

Co 

System failed to connect to a remote receiver 
after ‘n’ tries.

Verify the address book settings for the con-
tact are correct (i.e., modem device number, 
phone number to dial), verify the receiving 
device (fax or modem) is operational. Con-
tact technical support for assistance.

Cold Temperature Warning

T

Probe temperature drops below -4°F (-20°C).

Probe returns to normal operation after 
probe temperature rises above 0°F 
(-17.8°C).

Continuous Handle On 
Alarm

Q

Handle signal has been active for a programmed 
number of hours.

Call for service following the procedures 
established for your site.

CSLD Rate Increase Warn-
ing

T

An excessive amount of fluid leaked into the tank 
during a test period.

Call for service following the procedures 
established for your site.

Density Offset Warning

 T

The console calculated density offset amount 
exceeds the threshold amount: 

10.012 kg/m

3

 

(



0.625 lbs/ft

3

).

Check the density offset values configured 
for the probe. If these values are correct, the 
probe float may be contaminated, and 
should be replaced.
NOTE: This alarm message will continue to 
display (scroll) in the System Status box 
until you correct the cause of the problem.

Density Warning

T

Tank density is either:
• Greater than the tank density low limit plus 
1.00kg/m

3

 (0.062 lbs/ft

3

)

• Or is less than the tank density high limit minus 
1.00 kg/m

3

 (0.062 lbs/ft

3

)

Verify fluid density (retest when product 
density is within the tank density low and 
high limits.

Delivery Needed Warning

T

Product level dropped below programmed limit.

Call for a delivery.

Содержание TLS-3 Series










Отзывы: