manualshive.com logo in svg

VDO CONTISYS OBD -, Инструкция по эксплуатации

Поделиться
Скачать
VDO CONTISYS OBD - Скачать руководство пользователя страница 29

FastCheck

27

• Volvo S80 (99-06)

• Volvo XC90 (02-06)

Ensure the vehicle's ignition is OFF.

Connect the service tool to the required vehicle connector, refer to 

‘Diagnostic 

connector locations’, page 79

, for further information. 

Power for the service tool is provided by the vehicle connector. Once connected, the 
service tool will perform an internal self test and then the screen will display the version 
of the current software before displaying the main menu.

Use the 

 and 

 keys to select the 'FastCheck Airbag' application and press 

 

to confirm the selection. To return to the previous menu, press the 

 key.

Turn the vehicle's ignition ON.

Use the 

 and 

 keys to select the vehicle manufacturer and press 

 to confirm 

the selection.

Dependent upon the vehicle and application being run, you may be asked to choose 
the particular system fitted to the vehicle. Select the correct system using the 

 and 

 keys and press 

 to confirm.

Select the required menu option using the 

 and 

 keys and press 

 to confirm.

The service tool will attempt to establish communication with the vehicle system. If 
communication is unsuccessful, refer to 

‘Communication problems’, page 10

.

Read DTCs

If any DTC codes are present in the system, a screen will be displayed informing you 
how many codes were found. This will then be replaced by the first DTC code. DTC 
codes are generated according to the vehicle and system manufacturer.

The fault number is displayed first, followed by the DTC code. If the description text is 
too long to fit on the display, '[...]' appears in the bottom right corner of the screen. 

MAIN MENU

1.

EOBD

2.

FastCheck ABS

3.

FastCheck Airbag

4.

FastCheck Climate

5.

FastCheck EPB

6.

FastCheck SAS

7.

FastCheck Service

8.

FastCheck TPMS

9.

User Menu

1.

Read DTCs

2.

Clear DTCs

Содержание CONTISYS OBD -

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды