VDO CONTISYS OBD - Скачать руководство пользователя страница 23

Страница: 23 / 144

FastCheck

Safety instructions

WARNING: General safety

• All operations must be carried out in a well ventilated area away from open

flame and heat sources.

• Ensure the vehicle is stationary and the handbrake (parking brake) is applied

before carrying out any maintenance/diagnostic work.

WARNING: Air conditioning safety

• Servicing must only be carried out if you are familiar with both the vehicle

system and the test equipment.

• Air conditioning refrigerant is a hazardous liquid and when handled incorrectly

can cause serious injury. Suitable protective clothing, consisting of face
protection, heat proof gloves, rubber boots and rubber apron or waterproof
overalls, must be worn when carrying out operations on the air conditioning
system.

• Danger of asphyxiation, refrigerant gas is heavier than air and will collect in

vehicle inspection pits or confined spaces, always recover all refrigerant from a
damaged system before commencing work.

WARNING: Airbag safety

• All work on vehicle restraint systems should be carried out by trained personnel.

NEVER install accessories in the vicinity of driver, passenger or side airbags.

• Observe component manufacturers instructions for safety, handling and

installation of components.

• Airbags are classed as explosive devices and as such are subject to national

laws which must be followed. This includes storage and transportation.

• ALWAYS store removed airbags in a secure area away from other hazardous

materials.

• DO NOT connect or disconnect any wiring with the ignition ON. ALWAYS turn

the ignition switch to the 'OFF' position and allow at least 1 minute for the
system to discharge.

• NEVER expose system components to temperatures above 176°F (80°C).

• ONLY use approved diagnostic testers to diagnose faults, NEVER use multi-

meters or test lamps etc.

• ALWAYS disconnect all airbags and seat belt pre-tensionless before using a

multi-meter to check the wiring.

Содержание CONTISYS OBD -

















































































































































Результаты поиска

Содержание CONTISYS OBD -

Отзывы:

Бренды по названию

Популярные бренды

VDO CONTISYS OBD -, Инструкция по эксплуатации

Результаты поиска

Содержание CONTISYS OBD -

Отзывы:

Бренды по названию

Популярные бренды