VDO CONTISYS OBD - Скачать руководство пользователя страница 22

Страница: 22 / 144

FastCheck

Introduction

The 'FastCheck' applications allow the service tool to communicate with other system
control modules on the vehicle.

Connection to the specific system is via either the vehicle's EOBD (J1962) diagnostic
socket or by a system specific connector. Refer to the 'Vehicle Application List' to
determine the correct cable.

There are currently seven applications available.

FastCheck ABS

• FastCheck ABS allows you to read and clear any fault codes stored by the selected

system

FastCheck Airbag

• FastCheck Airbag allows you to read and clear any fault codes stored by the

selected system.

FastCheck Climate

• FastCheck Climate allows you to read and clear any fault codes stored by the

selected system.

FastCheck EPB

• FastCheck EPB (Electronic Parking Brake) allows you to read and clear any fault

codes stored by the selected system, and in addition can be used during brake
operation checks or brake pad replacement.

FastCheck SAS

• FastCheck SAS (Steering Angle Sensor) allows you to read and clear any fault

codes stored by the selected system, and in addition can be used to calibrate the
steering angle sensor.

FastCheck Service

• FastCheck Service allows you to reset, dependent upon vehicle, the oil service

interval indicator, service and inspection warning lights.

FastCheck TPMS

• The FastCheck TPMS (Tyre Pressure Monitoring System) function can be used to

reprogram tyre valves fitted with TPMS valves.

Содержание CONTISYS OBD -

















































































































































Результаты поиска

Содержание CONTISYS OBD -

Отзывы:

Бренды по названию

Популярные бренды

VDO CONTISYS OBD -, Инструкция по эксплуатации

Результаты поиска

Содержание CONTISYS OBD -

Отзывы:

Бренды по названию

Популярные бренды