background image

15

Approached

This alert is displayed for 30 seconds, from the moment the Transmitter has been detected as out of range

Range Limit

until the

Out of Range

warning is displayed. The message is a warning that the video signal is about to be

lost.

This message appears only when OSD display is enabled.

Video Signal Not

A link has been established between the Transmitter and the Receiver, but no video signal has been

Detected

detected. This message appears regardless of whether OSD display is enabled.

System Messages – No Link

These system messages may appear when no live video is displayed:

Alert

Description

Searching for

This message is displayed until a link is established. This may occur when the Transmitter is out of range

Transmitter

or unavailable, or when the Receiver has been removed from its list of paired devices.

Pairing in Progress

This message is displayed while the Transmitter is pairing with a Receiver.

For a detailed description of the pairing process, refer to

Multicasting to Multiple Monitor Units

.

Multicasting to Multiple Receivers

A single Transmitter can transmit video downlink to up to 4 Receivers. This is called

multicasting

. The

following procedure describes how to pair an additional Receiver with the same Transmitter.

NOTE

1. The Transmitter and Receiver provided in the same box are preconfigured to

au-tomatically search for and connect to each other. Therefore, there is no

need to perform this procedure on the Transmitter / Receiver delivered in the

same box.

2. Register one Receiver at a time to each Transmitter.

Pairing Additional Receivers with a Transmitter

To pair an additional Receiver with a Transmitter:

1. Set up the additional Receiver, as described in

Setting Up the Thor 800FT+ Receiver

. The

Receiver must be placed between one and ten meters from the Transmitter. To enable optimal

reception, each Receiver must be placed at least a few meters away from other Receivers.

After setting up the additional Receiver, the following message is displayed on the monitor

connected to the Receiver’s SDI or HDMI port:

"Receiver not registered to Transmitter."

2. From the Receiver, activate the OSD display. Navigate to the

Pairing

menu, and select

Start Pairing

.

Содержание Thor 800FT+





















Отзывы: