Vatech PHT-30CSS Скачать руководство пользователя страница 5

Страница: 5 / 162

Notice

vatech A9 (Model: PHT-30CSS) Installation Manual

Notice

This manual covers the installation procedures for the

vatech A9 (Model: PHT-

30CSS) digital X-ray imaging system

. The Installation Manual and the User Manual

are shipped with each hardware unit.

Brand name: vatech A9 (Model: PHT-30CSS)
Manufactured by: VATECH Co., Ltd.

In this manual, “equipment” refers to

vatech A9

In abbreviated forms, CBCT, CEPH, and PANO denote Cone Beam Computed

Tomography, Cephalo, and Panorama, respectively. They are interchangeably used.
The “Optional” in this manual means that the function or features are left to the

customer’s or user’s choice.
Review this manual thoroughly to ensure the proper installation. The

vatech A9

is in

steady improvement. The information contained in this manual may be subject to

change without notice, justification, or notification of the persons concerned.

VATECH Co., Ltd.

(manufacturer) reserves intellectual property rights (IPR) for this

manual and the equipment described herein. Reproduction of this manual partially or

fully is prohibited without the manufacturer’s consent.
Windows 10, NVIDIA, etc., are 3

parties’ prominent or registered trademarks

protected by related laws, and these trademarks are used in this manual just only for

explanation.
For further information not covered in this manual or the accompanying

documentation, please contact us:

Telephone:

(+82) 1588-9510

E-mail:

[email protected]

Website:

www.vatech.com

Address:

13, Samsung 1-ro 2-gil, Hwaseong-si, Gyeonggi-do, Korea

Manual Name: vatech A9 (Model: PHT-30CSS) Installation Manual

Version: 1.02

Publication Date: 2021-05

Содержание PHT-30CSS



































































































































































Результаты поиска

Содержание PHT-30CSS

Отзывы:

Похожие инструкции для PHT-30CSS

Бренды по названию

Популярные бренды

Vatech PHT-30CSS, Руководство по установке

Результаты поиска

Содержание PHT-30CSS

Отзывы:

Похожие инструкции для PHT-30CSS

Бренды по названию

Популярные бренды