Vari DSK-317.1/S, Перевод оригинальной инструкции

Страница: 25 / 44

VARI GLOBAL
2.4.6.1 Tiller implement KUR-70
Pict. 18: The tiller implement consists of two identical halves
1 , to be attached to the output shafts 2 of the gearbox and secured by a
retaining bolt with safety pin 3
(see Pict. 13).
2.4.6.2 Tiller implement KUR-112
Pict. 19: Attach on the basic triple-star shaped set 1 of KUR-70 the single-star edge sets: left edge angular 3 , left edge straight 5 ,
right edge angular 2 , right edge straight 4 . Secure the star-shaped sets with a retaining bolt with safety pin 3
(see Pict. 16).
2.4.6.3 Tiller implement KUK-96
Pict. 20: The tiller implement consists of two identical halves 1 , to be attached to the output shafts 2 of the gearbox and secured by a
retaining bolt with safety pin 3 (see Pict. 13).
2.4.6.4 Tiller implement KUK-125
Pict. 21: Attach on the basic triple-star shaped set
1 of KUK-96 the single-star edge sets: left edge 2 and right edge 3 . Secure the
star-shaped sets with a retaining bolt and safety pin 3 (see Pict. 17).
2.4.6.5 Cover T-20
The tiller implement 3 mus be fitted with covers 4
(Pict. 12).
Cover T-20 1 is to be attached according to
Pict. 14 on the side of the
gearbox under the upper screw 2 of the upper hitch Z-01 3
.

It is prohibited to operate the rotary tillers without the covers fitted.
2.4.6.6 Guiding wheel VK-GLOBAL
Attach the guiding wheel VK-GLOBAL according to
(Pict. 15) into holes
1 in the front part of the gearbox. Push up the wheel arm 2
to the required height and secure it 3 with the handle. There is a check hole next to the handle for easy position setting 4 , through which
it is possible to see notches made on the wheel arm. To be able to tighten the handle the hole must coincide with the notch (see detail on
Pict. 15).
2.4.6.7 Share N-3
The share holder with share N-3 5 is attached to the hitch Z-01 7 using a pin 6 with a safety pin
(Pict. 12). Once the required depth
is determined it is secured with the use of a split pin 8 inserted into the hole in the share holder where it passes through a notch in the
share 5 .
2.5 Putting in operation

First peruse the instructions for use 52 of all accessories! Especially those parts dealing with safety of operation,
assembly and use.

Before each use, check the tightness of all the screws especially those used to hold attachments in place.

The gearbox is supplied with required amount of oil. Nevertheless, check the oil level through the check and filling hole on the
right side of the gearbox.
2.5.1 Connecting the driving unit
Refer to the Instruction for use of the driving unit. The pin on the driving unit must fit into the hole in the rear of the gearbox.
2.5.2 Starting the engine
Starting the engine is described in the instructions for use of the driving unit and the engine.

Attention! The machine is fitted with an automatic centrifugal clutch. At speeds above the minimum the energy
will always transmit to the gearbox. Hence do not start the engine with engaged gear but keep it always in the
neutral gear “0”!
2.6 Controls
2.6.1 Shifting gears
The gearbox has three forward speeds and one reverse speed. The shifting of gears is done with the gear lever located on the left side of
the gearbox. The pointer on the gear lever points to the letters cast in the gearbox casing
(Pict. 3).
52
Peruse in particular the engine use manual and guiding handles and driving unit instructions for use.
25
R
ev
iz
e
0
4
/2
0
1
5