Vapac VIRTUOSO VE05-1P, Инструкция по установке и эксплуатации

Страница: 44 / 80

Page No 44 of 80 Vapac, Virtuoso VE Humidifier, Installation Manual, EN 2024-01, D301474 Iss 0
C
ModScan Register Variable Description R/W Saved Default
40037 36 Feed Manual Feed override 1=Feed on 0=off RW
40038 37 Drain Manual Drain override 1=Drain on 0=off RW
40039 38 ResetServiceHours 1=Reset R14 HoursToService RW
40040 39 ResetPCSCC 1=Reset R21 PCSCC RW
40041 40 ManualOverride 1=Manual Override 0=Normal Operation,
used with R 16,36,37 RW
40042 41 ModelChangeConfirm Used interally to stop operation while the
model type is changed 1=Stop 0=Normal
Operation RO
40043 42 Heartbeat Increments every 2 seconds, used to indicate
MODBUS connection RO
40044 43 UnitStatus2 Cylinder 2 Status 0=Standby, 1=Steaming,
2=Feeding, 3=Draining, 4=Unused, 5=Alarm RO
40045 44 LowOutputLevel1 Low output level setting 0-100% for
Cylinder 1 RW yes 80
40046 45 LowOutputDelay1 Low output level delay time setting 0-9999
min for Cylinder 1 RW yes 30
40047 46 LowOutputLevel2 Low output level setting 0-100% for
Cylinder 2 RW yes 60
40048 47 LowOutputDelay2 Low output level delay time setting 0-9999
min for Cylinder 2 RW yes 240
40049 48 FrostProtectTemp Temperature at which the unit goes into
frost protect mode RW yes 2
40050 49 FrostProtectDemand Demand setting for frost protect mode RW yes 2
40051 50 HumiditySensorOffset Humidity sensor Adjustment -10 to +10 % RW yes
40052 51 TotalDrainTime Time in seconds for a complete drain of the
cylinder RW yes 40
40053 52 TemperatureSensorOffset Temperature sensor adjustment -9 to +9 °C RW yes
40054 53 RelayOutputs
0 - not used
1 - RELAY_FEED1
2 - RELAY_FEED2
3 - RELAY_DRAIN1
4 - RELAY_DRAIN2
5 - RELAY_ALARM
6 - RELAY_RUN
7 - RELAY_WARNING Bitmap of Relay outputs
Relay 1 not fitted
Relay 2 Feed valve cylinder 1
Relay 3 Feed valve cylinder 2
Relay 4 Drain pump cylinder 1
Relay 5 Drain pump cylinder 2
Relay 6 Alarm (Fault)
Relay 7 Running
Relay 8 Warning (Fault) RO
40055 54 SerialBaudRate Modbus baud rate divided by 100 eg 1152
= 115200, 96 = 9600 RO yes 1152
40056 55 SerialParams Bits, Parity, Stop bits, 0=8N1, 1=8N2,
2=8E1, 3=8E2, 4=8O1, 5=8O2 RO yes 0
40057 56 ModbusAddress MODBUS Node Address 1-253 RO yes 1
40058 57 pFactor Humidity control PID Loop Proportional P
factor RW yes 500
40059 58 iFactor Humidity control PID Loop Integral I factor RW yes 100
40060 59 RunMinutes Minutes running 0-59 used internally for
hours run calculation RO yes