Vanco Evolution EVMX4K04 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

background image

www.vanco1.com

800.626.6445

17

TCP/IP CONTROL

The Evolution HDBaseT 4x4 Matrix Switcher boasts an option TCP/IP port for IP control.
Default settings: IP: 192.168.0.178; Subnet Mast: 255.255.255.0; Gateway: 192.168.0.1; Serial Port:
4001.
IP& gateway can be changed as you need, Serial Port cannot be changed.
Connect the Ethernet port of control device and TCP/IP port of 4K HDBaseT 4x4 Matrix Switcher, and set
same network segment for the 2 devices, users are able to control the device via web-based GUI or designed
TCP/IP communication software.

CONTROL MODES
4K HDBaseT 4x4 Matrix Switcher can be controlled by PC without Ethernet access or PC(s) within a LAN.

CONTROLLED BY PC
Connect a computer to the TCP/IP port of the 4K HDBaseT 4x4 Matrix Switcher, and set its network segment
to be the same as the 4K HDBaseT 4x4 Matrix Switcher’s (Default: 192.168.0.178).

Same Network
Segment as the
Switcher

«
...
15
16
17
18
19
...
»

Содержание Evolution EVMX4K04

























Отзывы:

Нет отзывов

Похожие инструкции для Evolution EVMX4K04

Бренд: KELCO Страницы: 41

Бренд: National Instruments Страницы: 23

Бренд: GALCO Страницы: 22

Бренд: Audio Authority Страницы: 12

EX ZS 92 S 22 VD F

Бренд: steute Страницы: 28

MIEN2208 Series

Бренд: Maiwe Страницы: 5

EdgeLens INT10G8SR56

Бренд: Garland Страницы: 76

T0-4 SE2 Series

Бренд: Eaton Страницы: 2

Бренд: SELS Страницы: 2

Digital Energy STS-400-25-3

Бренд: GE Страницы: 49

Бренд: Davey Страницы: 2

Бренд: Lindy Страницы: 5

Бренд: H3C Страницы: 77

SL-3-SL-4 STOP LIGHT SWITCH

Бренд: BENDIX Страницы: 4

Бренд: Zektor Страницы: 30

8 Port 10/100 Ethernet Switch

Бренд: OnQ Technologies Страницы: 14

Бренд: Tvone Страницы: 11

Бренд: IOGear Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды