Valor Inspire 600FS Скачать руководство пользователя страница 13

Страница: 13 / 64

5. GENERAL INSTALLATION REQUIREMENTS

5.1 Regulations, Standards and Law.

The installation must be in accordance with these instructions.

For the user’s protection, in the United Kingdom it is the law that all gas appliances

are installed by competent persons in accordance with the current edition of the Gas

Safety (Installation and Use) Regulations. Failure to install the appliance correctly

could lead to prosecution. GAS SAFE REGISTER require their members to work to

recognised standards.

In the United Kingdom the installation must also be in accordance with:

All the relevant parts of local regulations.

All relevant codes of practice.

The relevant parts of the current editions of the following British Standards:-

BS EN 1856 Part 1

Chimneys - Requirements for metal chimneys.

BS 5440 Part 1

Installation of flues.

BS 5440 Part 2

Installation and maintenance of flues and ventilation for gas

appliances of rated input not exceeding 70 kw net (1st, 2nd

and 3rd family gases).

BS 6461 Part 1

Masonry chimney & flues - Installation.

BS 1251

Fireplace components.

BS 5871 Part 2

Installation - Inset LFE gas fires.

BS 6891

Gas pipework installation.

In England and Wales, the current edition of the Building Regulations issued by the

Department of the Environment and the Welsh Office.

In Scotland, the current edition of the Building Standards (Scotland) Regulations

issued by the Scottish Executive.

In Northern Ireland, the current edition of the Building regulations (Northern

Ireland) issued by the Department of the Environment for Northern Ireland.

In the Republic of Ireland the installation must be carried out by a competent

person and also conform to the relevant parts of:

a) The current edition of IS 813 “Domestic Gas Installations”

b) All relevant national and local rules in force.

Where no specific instructions are given, reference should be made to the relevant

British Standard Code of Practice.

5.2 Ventilation requirements.

Normal adventitious ventilation is usually sufficient to satisfy the ventilation

requirements of this appliance. In GB reference should be made to BS 5871 Part 2

and in IE reference should be made to the current edition of IS 813 “Domestic Gas

Installations” which makes clear the conditions that must be met to demonstrate that

sufficient ventilation is available.

Page 13

GDC Group Ltd. AUG 2016

INSTALLER GUIDE

Содержание Inspire 600FS

































































Результаты поиска

Содержание Inspire 600FS

Отзывы:

Бренды по названию

Популярные бренды

Valor Inspire 600FS, Инструкция для установщика и владельца

Результаты поиска

Содержание Inspire 600FS

Отзывы:

Бренды по названию

Популярные бренды