Valor 910 Brunswick Скачать руководство пользователя

Страница: 24 / 30

Operating the burner.

When the pilot burner is operating properly, gradually turn the control knob anti-

clockwise to 'HIGH' position. (Depress the knob slightly to get past the pilot ignition

position). The main burner should now light.

Depress the control knob slightly to release from the 'HIGH' position and turn back

(clockwise) to 'LOW'. While turning, the burner flames should gradually become lower

but remain alight. Depress the control knob slightly to release from the 'LOW' position

and turn back (clockwise) to the Pilot ignition position. The main burner should

extinguish but the pilot should remain alight. Depress the control knob slightly and

turn back (clockwise) to turn OFF. This will extinguish the pilot.

While cooling, the ceramic fuel effects may make some crackling noises. This is quite

normal.

Note i)

If the flames go out while setting the control, repeat the full lighting

procedure. If the flames repeatedly go out have the stove serviced.

ii)

Please note. When first turned on the flames will appear predominantly

blue. The fuel effect pieces will take time to warm up. Although some glow

will be seen after approximately ten minutes, the full visual effect will only

be apparent after a somewhat longer time.

iii)

The appliance will operate to its maximum potential if the flue is primed

during the first 20 – 30 minutes of operation. To do this, simply slide the

control button to its highest setting. This will also burn off any carbon

deposits that may have formed during previous operations.

iv)

If operating the appliance for long periods it is beneficial occasionally to

change the settings. This will also help to remove any carbon deposits

that may form during operation.

GAS CONSUMPTION

Model 910

Has a maximum natural gas input of 5.50kW (Gross)

Has a maximum natural gas output of 4.02kW

Has a minimum natural gas input of 2.3kW (Gross)

Has a minimum natural gas output of 1.68kW

Model 910 when converted using kit number 0591011

Has a maximum propane gas input of 5.40kW (Gross)

Has a maximum propane gas output of 3.94kW

Has a minimum propane gas input of 3.8kW (Gross)

Has a minimum propane gas output of 2.77kW

Page 24

GDC Group Ltd. 2014

OWNER GUIDE

Содержание 910 Brunswick































Результаты поиска

Содержание 910 Brunswick

Отзывы:

Похожие инструкции для 910 Brunswick

Бренды по названию

Популярные бренды

Valor 910 Brunswick, Инструкция для установщика и владельца

Результаты поиска

Содержание 910 Brunswick

Отзывы:

Похожие инструкции для 910 Brunswick

Бренды по названию

Популярные бренды