background image

5.7  FEDERAL COMMUNICATION COMMISSION (FCC) AND INDUSTRIAL 

CANADA (IC) STATEMENTS

5.7.1 FEDERAL COMMUNICATION COMMISSION (FCC)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.  This device may not cause harmful interference.
2.  This device must accept any interference received, including interference that may cause undesired operation.

Caution:

 Any changes or modifications not 

expressly approved by the party respon-

sible for compliance could void the user’s 

authority to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may 
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in 
which case the user will be required to correct the interference at his own expense.

EC 30W/EC 97W: CONTAINS FCC ID: SQGBL651

FCC Radiation Exposure Statement
The product complies with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as 

described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set 

the device to lower output power if such function is available.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

5.7.2 INDUSTRY CANADA (IC)

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
1.  This device may not cause interference; and 
2.  This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux 

deux conditions suivantes:
1.  l’appareil ne doit pas produire de brouillage;
2.  l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le 

fonctionnement.

EC 30W/EC 97W: CONTAINS IC: 3147A-BL651

Radiation Exposure Statement
The product complies with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as 

described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set 

the device to lower output power if such function is available.
Déclaration d’exposition aux radiations
Le produit est conforme aux limites d’exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement 

non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si 

l’appareil peut être conserve aussi loin que possible du corps de l’utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si 

une telle fonction est disponible.

25

EC70EN - 6/2022 | Stonel product publication 105509revA

Содержание Stonel Eclipse EC Series





























Отзывы: