Valmet Stonel Eclipse EC Series Скачать руководство пользователя страница 21

Страница: 21 / 28

4.2.2 VCT WITH AS-INTERFACE COMMUNICATION AND EXTENDED ADDRESSING (97S & 97W)

CONTINUED

Power/Fault LED status
AS-i status LED

Fault description

LED off

Device does not have power

Solid green

Normal operation

Flashing red/green

Output shorted

Flashing red/green

No magnet detected

Flashing red/green

Internal sensor fault - sensor may need replacing

Flashing yellow/red No data exchange (device address = 0)
Solid red

No data exchange

Specifications for Wireless Link

Communication

Bluetooth® technology; single mode
(not compatible with Bluetooth® Classic)

Frequency band

2.402-2.480 Ghz

Transmit power

4dBm or ~2.5 milliwatts

Data rate

1 Mbit/second; effective information transmit rate
~10 Kbits/second

Range

Up to 100 meters (330 feet) in free space. Range is
reduced by obstructions between handheld device
and Wireless Link VCT. Line of site is not necessary.

Registrations

FCC, IC, CE

CE compliance

Exceeds industrial compliance standards

VCT identification

VCTs in range will be displayed in order of signal
strength

VCT link

One device accessed at a time between client (hand-
held device) and server (VCT). Each server accessed
by one client at a time

Application

StoneL Wireless Link available from the App store

Hand-helds

Compatible with iPhone® and iPad® with iOS 9 or
later

Wink feature
The Wink feature provides the capability of setting the closed or open

LEDs to flash or wink at a 2 Hz rate. This feature aids in physically

locating the unit on the network. It does not change valve state

indication in the control system.

Bench test procedure and sensor setting instructions

1. To test sensors, it is best to connect to an AS-i bus using an

AS-i power supply so that communication can also be tested.

However, if a network is not available, to set the open and closed

set points, use a 24 VDC power supply. Connect 24 VDC+ to

AS-i+ and 24 VDC- to AS-i -.

2. Attach indicator such that the closed quadrants will face out when

in the closed position. This figure shows a Red Closed visual

indicator in the closed position.

gne

Green

ree

Save set-points:
a.

Operate actuator to the closed position.

Press and hold SET CLOSED button until closed LED is lit (2

seconds). Release button.

Operate actuator to the open position.

Press and hold SET OPEN button until the open LED is lit (2

seconds). Release button.

NOTE: If red or green LEDs flash when trying to set the set-point,

the magnet is too far away from the sensing element. Adjust Visual

Indicator drum to bring the magnet slightly closer to the sensing unit

and try again.
3. Setpoints are retained even after power is removed.
4. To electrically test the solenoid output, the unit should be

connected to an AS-i bus and commanded to turn on. Optionally,

the solenoid can be energized via the Bluetooth app if the device

is configured with Bluetooth capability and is unlocked.

Note
If using only one of the sensors for valve position feedback, either

sensor may be used independently.

WARNING

DO NOT APPLY EXTERNAL POWER TO THE OUTPUT

TERMINALS. THIS WILL CAUSE PERMANENT DAMAGE TO

THE UNIT.

Caution:

Performing this procedure will cause the

sensor inputs to change state. Performing this procedure
is not recommended during a live process.

EC70EN - 6/2022 | Stonel product publication 105509revA

Содержание Stonel Eclipse EC Series





























Результаты поиска

Содержание Stonel Eclipse EC Series

Отзывы:

Похожие инструкции для Stonel Eclipse EC Series

Бренды по названию

Популярные бренды

Valmet Stonel Eclipse EC Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание Stonel Eclipse EC Series

Отзывы:

Похожие инструкции для Stonel Eclipse EC Series

Бренды по названию

Популярные бренды