MCP-4J Quick Start Guide
IS0368
Valco Melton
38
Set the Pressures - Continued
Purge Pressure %
(All Applications)
Purge Pressure -
Purge Pressure -
Purge Pressure -
Purge Pressure -
Purge Pressure - The pressure setting when the machine is at
zero speed.
The number on the left side of the pressure screen refers
to the EPC number (two EPCs are available on some
models of the MCP-4J Control Unit. The second EPC is the
0-10 Volt output for speed tracking. Both EPCs are
programmed in the same way; just be certain the desired
EPC number appears on the screen before programming.
To switch between EPCs, press the Pressure Button until
the desired EPC number appears.
EPC Output Mode (EPC2 ONLY)
0-10 VDC or 0-20 mA
0-10 VDC or 0-20 mA
0-10 VDC or 0-20 mA
0-10 VDC or 0-20 mA
0-10 VDC or 0-20 mA - If EPC 2 is enabled, the user can set the
output signal to either 0-10 VDC or 0-20 mA.
Helpful Hints about Pressures
The four pressures/speeds are dependent upon each other. For example,
the first speed setting can never be greater than the second speed setting,
and the second speed setting can never be greater than the third, and so
on. Also, the second speed setting can never be less than the first speed
setting, the third speed setting can never be less than the second speed
setting, and so on. Therefore, if you cannot set speeds to where you want
them (the Plus/Minus Arrow Buttons will not increase or decrease the
setting), check all four of the settings. Use the Left Arrow and Right Arrow
Buttons to move through all pressures/speeds and check them. Reset
them as necessary using the Plus/Minus Arrow Buttons. You can also go
back to factory defaults by pressing the Erase Button until the setting will no
longer change.
Содержание MCP-4J
