Vaisala AWS310-SITE Скачать руководство пользователя страница 131

Страница: 131 / 176

When a value is expressed as

N/A

, it indicates that the calibration factor has been

altered but not saved, the sensor has not been measured, its measurement channel
has failed, or the sensor is disabled.

5. To read the latest sensor status and measurement values, select

Refresh

More Information

‣

Sensor Status Values (page 149)

6.6 Troubleshooting with Commands

For most of the sensor inputs, you can use data validation parameters to check the following
quality parameters for the measurements:

• Maximum value: the maximum climatological value for the sensor measurement.
• Minimum value: the minimum climatological value for the sensor measurement.
• Step change: the maximum step change for the sensor value between two consecutive

measurements.

If the sensor value is outside the maximum or minimum values, or it has altered more than
the maximum step change allows, data is flagged as

INVALID

. Invalid data is typically

displayed as

/////

(this is a parameter that you can set). If a sensor displays invalid data,

this is an indication that the sensor is faulty or out of calibration, or there is a problem in
powering or measuring the sensor.

6.6.1 Checking Errors

The

/ E>

prompt in the terminal window means that there are errors. Errors indicate that

there is something wrong with the sensors or the configuration.

1. Check the active errors.

/ E>

errors

2. Clear the active errors.

/ E>

errors

clear

3. Write down the error information and contact Vaisala technical support.

Chapter 6 – Troubleshooting

129

Содержание AWS310-SITE

















































































































































































Результаты поиска

Содержание AWS310-SITE

Отзывы:

Похожие инструкции для AWS310-SITE

Бренды по названию

Популярные бренды

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Результаты поиска

Содержание AWS310-SITE

Отзывы:

Похожие инструкции для AWS310-SITE

Бренды по названию

Популярные бренды