Vaillant VR 90 Скачать руководство пользователя страница 29

Страница: 29 / 32

Installation manual remote control device VR 90 0020055329_00

Function

Meaning / Explanation

Switch-on room temperature

The utilisation of the room sensor in the remote control device (RCD) is adjustable:

none, intervention, (factory setting: none).

The switch-on room temperature is used to include the current room temperature in a reference room in
the calculation of the flow temperature. The room temperature sensor of the assigned RCD is used if the
function is active.

Current room temperature
correction

The displayed value of room temperature can, if required, be shifted upwards or downwards by +/-3 °C.

Target inlet temperature

Represents the inlet temperature in a heating circuit calculated by the controller on the basis of the
pre-set parameters.

Actual inlet temperature

The actual inlet temperature in a heating circuit.

Table 7.1 Overview of functions (continued)

Overview of functions 7

Содержание VR 90

































Результаты поиска

Содержание VR 90

Отзывы:

Похожие инструкции для VR 90

Бренды по названию

Популярные бренды

Vaillant VR 90, Руководство по эксплуатации и установке

Результаты поиска

Содержание VR 90

Отзывы:

Похожие инструкции для VR 90

Бренды по названию

Популярные бренды