Vaillant MultiMatic 700/2 Скачать руководство пользователя страница 97

Страница: 97 / 112

multiMATIC 700/2

Notes

10/2015

Training 0020228700_00

In the event that a combination of "System diagram" and "VR 70 configuration" is se-
lected that is not permitted, the fault message "

System diagram selection incorrect

or "

VR 70 configuration incorrect

" is displayed on the controller.

If a combination of "System diagram" and "VR 71 configuration" is selected that is not
permitted, the fault message "

System diagram selection incorrect

" is displayed on

the controller.

Assignment of system diagrams to heat generators

System diagram

Heat generator

1, 2

Conventional heat generator

6, 7

geoTHERM 3 kW Hybrid heat pump

8, 9, 12

flexoTHERM heat pump

8, 9, 10, 11, 12, 13

aroTHERM heat pump

5.2.3

Settings and displays/indicators on the VR 91

Front view of the VR 91

The VR 91 remote control unit is a wire-bound remote control unit for

one zone

combination with the VRC 700 controller. It communicates with the boiler exclusively
via eBUS.

Only

one

VR 91 can be used in conjunction with VR 70.

Up to

two

VR 91 can be used in conjunction with VR 71.

Auto

13.5 °C

11:54

23.0 °C

Desired heating temp. 23.0 °C

Op. mode

Содержание MultiMatic 700/2

















































































































Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды

Vaillant MultiMatic 700/2, Тренинг по продукту

Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды