Vaillant MultiMatic 700/2 Скачать руководство пользователя страница 89

Страница: 89 / 112

multiMATIC 700/2

Notes

10/2015

Training 0020228700_00

Installation, start-up

As a general principle, the instructions and information

– in particular safety instruc-

tions

– from the relevant installation instructions must be observed.

5.1

Installation

5.1.1

Installing the controller in the unit electronics box

First check the switch cabinet type:

Old type of electronics box:

ecoTEC plus unit electronics box with multiMATIC 700/2

Installation:

●

Insert the short ends of the three-pin plug con-

nector (2) included with the controller into the three
horizontal openings on the controller's PCB (1).

●

Carefully push the controller with the plug con-

nector into the plug-in connection on the electronics
box.

Rear view of multiMATIC 700/2

Installing the controller in the unit electronics box is not permitted for systems with the

geoTHERM 3 kW heat pump.

Содержание MultiMatic 700/2

















































































































Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды

Vaillant MultiMatic 700/2, Тренинг по продукту

Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды