Vaillant MultiMatic 700/2 Скачать руководство пользователя страница 101

Страница: 101 / 112

multiMATIC 700/2

Notes

10/2015

Training 0020228700_00

Maintenance/troubleshooting

6.1

Maintenance messages

Maintenance messages appear on the upper line in the controller's basic display.

In  the  example  on  the  right,  the  maintenance
message  has  been  triggered  by  the  boiler
electronics.
The  following  is  an  overview  of  the  possible
maintenance messages.

Message

Note/information

Maintenance

The controller service request is displayed. Pro-
grammed with "Menu > Installer level > Service
information > Service date"

Heat generator maintenance

The boiler service request is displayed

Low water pressure, heat generator

Low water pressure, add. module

Service ventilation unit

The ventilation unit service request is displayed

Heat pump maintenance

The heat pump service request is displayed

Low water pressure

Restricted operation

Comfort protection

Solar circuit protection active (VR 70)

The solar circuit protection temperature has been
reached or exceeded and is blocking the solar
pump.

Содержание MultiMatic 700/2

















































































































Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды

Vaillant MultiMatic 700/2, Тренинг по продукту

Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды