Vaillant MultiMatic 700/2 Скачать руководство пользователя страница 71

Страница: 71 / 112

multiMATIC 700/2

Notes

10/2015

Training 0020228700_00

Type of circuit

Setting the type of circuit has an effect on the parameters displayed for the heating cir-
cuits, the zones, and on the VRC 700's control strategy. The following provides an
overview of which parameters are displayed in the system configuration:

Setting

Parameters displayed in the "Heating circuit 1/2/3" sub-menu

Inactive

None

Heating

Status

Cooling possible

Target flow temp.

Room temp. mod.

Current temperature (heating circuit 2 only)

Dew point monitoring

Excessive temp. (heating circuit 2 only)

Min. cool. fl. tgt temp.

Max limit outs.temp.

Cooling start temperature

Heating curve

Offset dew point

Minimum temperature

Status ext. heat dem.

Maximum temperature

Pump status

Auto Off mode

Mixer status (heating circuit 2 only)

Fixed value,

Pool

Status

Maximum temperature

Target flow temp.

Target flow temp.: Day

Current temperature (heating circuit 2 only)

T.fl.temp.: Set-back

Excessive temp. (heating circuit 2 only)

Status ext. heat dem.

Max limit outs.temp.

Pump status

Minimum temperature

Mixer status (heating circuit 2 only)

DHW

Target cylinder temp.

Pump status

Ret.fl.incr.

Target return temp.

Mixer status (heating circuit 2 only)

Содержание MultiMatic 700/2

















































































































Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды

Vaillant MultiMatic 700/2, Тренинг по продукту

Результаты поиска

Содержание MultiMatic 700/2

Отзывы:

Бренды по названию

Популярные бренды