background image

4

Installation and maintenance instructions ecoTEC plus 937 0020031552_06

Notes on the documentation

The following information is intended to help you 
throughout the entire documentation. 
Further documents apply in combination with this instal-
lation and maintenance manual.
We accept no liability for any damage caused by failure 
to observe these instructions.

1.1 

Documents also having validity

Always observe all installation instructions for struc-
tural parts and components of the system when 
installing the ecoTEC plus 937. These installation 
instructions are enclosed with the various system 
components as well as additional components.
Also observe all the operating instructions included 
with the system components.

1.2 Storing 

documents

Pass these installation instructions and all other 
applicable documents and, if necessary, any required 
aids to the system operator.

He will be responsible for storing them so that the 
instructions and aids are available when required.

1.3 Symbols 

used

The symbols used in the manual are explained below:

a

Symbol denoting danger

imminent danger to life
Risk of severe personal injury
Risk of slight personal injury



e

Symbol denoting danger

Risk of death from electric shock

b

Symbol denoting danger

Risk of material damage
Risk of damage to the environment


i

Symbol denoting additional useful tips and 
information

 

>

Symbol for a required task

>

>

>

1.4 

Validity of the manual

This installation manual applies exclusively to the unit 
with the following part number:

0010003809

The part number of the unit can be obtained from the 
identification plate. The 7th to 16th digits of the serial 
number form the article number.

1.5 Identification 

plates

The identification plate of the ecoTEC plus 937 is 
located on the underside of the unit.

1.6 CE 

label

CE labelling shows that the appliances comply with the 
basic requirements of the following directives:

Directive 

2009/142/EEC

 of the Commission with 

revisions
"Directive for Harmonisation of Legal Regulations of 
the Member States for Gas Consumer UNits" 
(Gas equipment directive)
Directive 

92/42/EEC

 of the Commission with revi-

sions
"Directive Concerning the Efficiency of New Hot 
Water Heating Boilers Fired by Liquid or Gaseous 
Fuels“ (Efficiency directive)
Directive 

2006/95/EEC

 of the Commission with 

revisions
"Directive Concerning Electrical Operating Equipment 
for Use Within Specific Voltage Limits“ 
(Low voltage directive)
Directive 

2004/108/EEC

 of the Commission with 

revisions
"Directive Concerning Electromagnetic Compatibility"

The units comply with the prototype described in the EU 
Prototype Test Approval:
PIN-No. CE-0085BP0464
The units comply with the following standards:

EN 483
EN 625
EN 677
EN 50165
EN 55014
EN 60335-1
EN 60529
EN 61000-3-2
EN 61000-3-3









1 Notes on the documentation

Содержание ecoTEC plus 937

















































































Отзывы: