Vacon NX 8000 Solar Series Скачать руководство пользователя

Страница: 36 / 44

36 • vacon

START UP

Tel: +358-201-2121 • Fax: +358-201-212 205

6.1.4.1

Description of push buttons

reset

This push button is used to reset active faults.

select

This push button is used to switch between the two last displays.

enter

The Enter push button serves to:

Restore the fault history (2-3 seconds)

Push button browser up

Browse the main menu and the pages of different submenus.

Push button browser down

Browse the main menu and the pages of different submenus.

Push button Menu left

Return to the menu.

Push button Menu right

Go forward in the menu.

To start the inverter

To stop the inverter

6.1.5

Browsing the control panel

Data on the control panel is arranged in menus and submenus. Menus are used, for example, to dis-

play control signals and the measurements of reference values and faults shown

The first menu level has menus from M1 to M7 and it is called

Main menu

. The user can browse the

main menu using the Browse push buttons

up and down. The chosen submenu can be accessed

from the main menu using the Menu push buttons. When there are pages under the menu or page
shown, you will see an arrow ( ) in the bottom right corner of the display and you will be able to
access the following menu level by pressing the

Push button Menu right





start

stop



V14

READY

Local

RUN

Monitor

Location

Description

Number of available elements;

element value

Содержание NX 8000 Solar Series













































Результаты поиска

Содержание NX 8000 Solar Series

Отзывы:

Похожие инструкции для NX 8000 Solar Series

Бренды по названию

Популярные бренды

Vacon NX 8000 Solar Series, Руководство пользователя

Результаты поиска

Содержание NX 8000 Solar Series

Отзывы:

Похожие инструкции для NX 8000 Solar Series

Бренды по названию

Популярные бренды