Vacon NX 8000 Solar Series Скачать руководство пользователя страница 37

Страница: 37 / 44

START UP

vacon • 37

24-hour support: +358 (0)201 212 575 • Email: [email protected]

6.1.5.1

Monitoring menu

To enter the Monitoring menu from the Main menu, press the Push button Menu right when the lo-

cation indication M1 appears in the first line of the screen. The following figure shows how to view

the monitored values.

The monitored signals have the indication V#.# and are listed in the following table. Values are up-

dated every 0.3 seconds.

This menu is used only to verify the signals. Values can not be modified.

Code

Parameter

Min

Max

Unit

Description

V1.1

Output power

1000

1707

Output power of inverter, with compensated
LCL filter losses.

V1.2

Total energy kWh

4,29E+09

kWh

1837

Total energy of inverter fed into the grid.

V1.3

Energy today kWh

6553,5

kWh

1708

Energy fed into the grid today.

V1.4

Energy yesterday

6553,5

kWh

1733

Energy fed into the grid yesterday.

V1.5

DC voltage refer-

ence

150

1200

Used DC voltage reference by the regenerative
unit in % of the nominal DC voltage.

V1.6

DC-link voltage

1000

1839

Filtered DC-link voltage in Volt.

V1.7

Unit temperature

-50

200

°C

1109

Temperature of the unit in Celsius

V1.8

AC voltage

1000

1709

AC voltage measured on the grid side of the
main contactor by an external measurement
circuit.

V1.9

AC frequency

-60

1835

Grid frequency in Hz. The sign indicates the
phase order. Can be monitored only when
UNIT is in RUN state.

V1.10

Output current

Varies

1834

Output current of the inverter coming out of
the cabinet (transformers inside cabinet are

taken into consideration).

V1.11

Run time total [h]

99999999

1836

Total time the inverter has been running.

V1.12

Run time today

255

1731

The time the inverter has been running today.

V1.13

Run time yesterday

255

1732

The time the inverter ran yesterday.

V1.14

Grid connections

4,29E+09

1706

Total number of times the inverter has closed

the main contactor and connected to the grid.

V1.15

Standby remaining

65535

1201

Remaining time in standby mode, if standby

mode is activated.

Table 6-1. Monitoring values

RUN

READY

Local

Monitor



V14

RUN

READY

Local

V1.1

Output power

19.4 kW

RUN

READY

Local

V1.1

Daily energy

125 kWh

Содержание NX 8000 Solar Series













































Результаты поиска

Содержание NX 8000 Solar Series

Отзывы:

Похожие инструкции для NX 8000 Solar Series

Бренды по названию

Популярные бренды

Vacon NX 8000 Solar Series, Руководство пользователя

Результаты поиска

Содержание NX 8000 Solar Series

Отзывы:

Похожие инструкции для NX 8000 Solar Series

Бренды по названию

Популярные бренды