Vacon NX 8000 Solar Series Скачать руководство пользователя страница 43

Страница: 43 / 44

MAINTENANCE AND TROUBLESHOOTING

vacon • 43

24-hour support: +358 (0)201 212 575 • Email: [email protected]

MCC Fault

Contactor acknowledgment is used
through digital input and close com-
mand is given without response within
the time set with parameter “MCont
FaultDelay”

Check the main power switch of the

Drive and Acknowledge input.

LCL Tempera-
ture

LCL Overtemp trip from digital input.

Check the LCL filter and signal connec-
tion. Check fan

AC VoltMax Trip AC voltage on line side is above the max

limit.

Check AC Voltage

AC VoltMin Trip AC voltage on line side is below the min

limit.

Check AC Voltage

FreqOverLimit

AC frequency on line side is above the
max limit.

Check AC Frequency

FreqUnderLimit AC frequency on line side is below the

min limit.

Check AC Frequency

DC Ground
Warning

DC Insulation measurement signal has
gone above the warning limit.

Check DC Insulation

DC Ground
Fault

DC Insulation measurement signal has
gone above the fault limit.

Check DC Insulation

Surge Alarm

Surge alarm from digital input.

Remove fault situation from external
device.

Fieldbus

Heartbeat signal from touchpad panel is
missing while running in array configu-
ration.
Warning = inverter not active
Fault = inverter active

Check touchpad panel. Check the con-
trol place

Input Switch

Input Switch in wrong state

Check the input Switch

Table 7-1. Fault codes

Содержание NX 8000 Solar Series













































Результаты поиска

Содержание NX 8000 Solar Series

Отзывы:

Vacon NX 8000 Solar Series, Руководство пользователя, Страница: 43 / 44

Результаты поиска

Содержание NX 8000 Solar Series

Отзывы: