UTICA BOILERS UCS-380 Скачать руководство пользователя страница 98

Страница: 98 / 102

P/N 240011775 Rev. A [02/02/17]

HEAT EXCHANGER CLEANING KIT INSTRUCTIONS

Ignition Flame

Detection Electrode

Control bottom

Support Bracket (4

Screws)

Air Mixer/Blower

Assembly

Control

Top of Condensate Trap

Gas Valve

Gas Valve Nut to Mixer

Assembly

Figure 4 - 380- Support Bracket and Control

Figure 5 - Hose Removed From Top of Condensate

Trap (380 Shown)

Hose From Heat

Exchanger to Condensate

Trap
Top of Condensate Trap

23.

Re-install hose to condensate trap. See Figure 5.

24.

Gently remove cover used to protect components from

debris and cleaning fluid.

25.

Remove duct tape from gas line.

26.

Remove protector from target wall insulation in rear of

heat exchanger chamber.

27.

Inspect heat exchanger gasket replace if necessary.

28.

Place Combustion chamber cover assembly back into

place. Tighten nuts securely (4 nuts-240, 6 nuts -380).

29.

Place gasket between gas valve and mixer. Tighten nut

securing gas valve to mixer.

30.

Re-connect ground and wire to ignition/flame detection

electrode.

31.

Re-connect wire harnesses to blower assembly. See Figure 2.

32.

380 - reattach supporting bracket and control. Tighten four

(4) screws securing bracket. See Figure 4.

33.

Place control in up position.

34.

Turn power and gas on.

35.

Check for leaks in gas line.

36.

Replace front panel. Secure with screws.

37.

Adjust Parameters as indicated A-D:

Содержание UCS-380







































































































Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды

UTICA BOILERS UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды