UTICA BOILERS UCS-380 Скачать руководство пользователя страница 48

Страница: 48 / 102

8 - ELECTRICAL CONNECTIONS

8.12 Frost Protection

Frost protection in combination with ON/Off

thermostat.

•

If ON/Off thermostat is used, protect any rooms where

there is a risk of freezing by using freeze thermostat

(FT). Radiator valves or zone where there is risk of

freezing must be open.

•

Connect frost thermostat in parallel with On/Off room

thermostat (RT

) to ON/Off_OT terminals of control

board connection.

Frost protection in combination with outdoor

temperature sensor.

• Heating system can be protected against freezing in

combination with

1 K

outdoor temperature sensor.

Radiator valve or zone must be open where there is a

risk of freezing.

• Connect

1 K

outdoor temperature sensor to "T out"

terminals of control board.

• Frost protection activates when

1 K

outdoor

temperature sensor reads a temperature lower than

10°F (-10°C ). This can be adjusted using parameter

P30. Circulation pump will switch on and operate

continuously until the outdoor temperature increases

past value set on parameter P30.

FIGURE 8-13 Frost Protection in Combination with

ON/OFF Thermostat

8.11 10 K

Ω DHW Indirect Water Heater

Connect 10 K

Ω DHW indirect tank sensor or thermostat

(TS

) to "

T dhw

" terminals on control board.

10 K

FIGURE 8-12 10 K

Ω Indirect Water Heater Thermostat

8.13 Pump Anti-Seize Protection

• If the boiler is in standby for 76 hours the pump will run

1 minute to prevent seizing.

PN 240011662 Rev. K [01/31/2020]

Содержание UCS-380







































































































Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды

UTICA BOILERS UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды