UTICA BOILERS UCS-380 Скачать руководство пользователя страница 77

Страница: 77 / 102

13 - TROUBLE SHOOTING

Troubleshooting Chart 1

E02 - Supply Sensor Short
E03 - Supply Sensor Open
E04 - Heat Exchanger Temp.
E05 - Heat Exchanger Temp.
E06 - Return Sensor Short
E07 - Return Sensor Open
E08 - Low Return Temp.
E09 -High Return Temp.

Locate Appropriate Sensor

See Figure 1 (page) and

Figure (Wire Diagram)

Trace wire leads. Are all

connections tight and wires

undamaged?

YES

Check continuity across

sensor.

OK?

YES

Repair wire

and/or fix

connection.

Check sensor element is

properly installed in pipe.

YES

Replace

Sensor

Replace

Control Board

Re-Install

Sensor Properly

Check sensor resistance

and compare to

temperature resistance

curve (Figure 13-1 page

87. (Remove sensor if

needed). OK?

YES

Replace

Sensor

Note

DOMESTIC HOT WATER SENSOR: If the DHW sensor is shorted it will act as a closed thermostat and boiler will

continuously fire.

PN 240011662 Rev. K [01/31/2020]

Содержание UCS-380







































































































Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды

UTICA BOILERS UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды