UTICA BOILERS UCS-380 Скачать руководство пользователя страница 75

Страница: 75 / 102

13 - TROUBLE SHOOTING

13.3 Error History

Boiler control is equipped with error memory which, records

last 16 errors. In addition to storing error codes, the following
data is also saved:

•

Number of times that the error occurred: (

n:xx).

• Boiler operating mode selected (St:xx).
• The supply temperature (t1:xx) and the return

temperature (t2:xx) when the error occurred.

To view the error history, enter access code 0012.

13.4 Error History

Readout

• Press two

buttons simultaneously and then (+)

button until the

symbol flashes on the menu bar.

• Select the installers menu using

button. "CODE"

appears on the display.

• Use (-) or (+) button to input installer code 0012.
• Press

button. "

Er:xx

" appears on the display.

• The fault list can be displayed by pressing (-) or (+)

button.

•

Confirm using

button. "Er:xx" is displayed with

"xx"

flashing = Last error which occurred, for example

"2".

• Use (-) or (+) buttons to scroll through faults.
• Press

button to display details of faults or

shutdowns.

• Press (-) or (+) buttons to view the following

information:
n:1

= Number of times that the error occurred.

hr = The number of operating hours.

St = State.

Su = Sub-status.

t1 = Supply temperature ºF/ºC.

t2 = Return temperature ºF/ºC. t3 = DHW tank

temperature ºF/ºC.

t4 = Outdoor temperature ºF/ºC (Only with an outdoor

temperature sensor).

t5 = Solar panel temperature ºF/ºC. t6 = Flue gas

temperature ºF/ºC.

Sp = Internal set point ºF/ºC.

= Ionization current (μA).

nf = Fan speed in rpm.

Pr = Water pressure psi/bar.

Po= Supplied relative heat output (%).

• Press

button to interrupt display cycle. "Er:xx" is

displayed with "xx"

flashing = Last error which occurred.

• Use (-) or (+) button to scroll through faults.
• Press

button to show fault list.

• Press

button 2 times to exit error history.

PN 240011662 Rev. K [01/31/2020]

Содержание UCS-380







































































































Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды

UTICA BOILERS UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды