UTICA BOILERS UCS-380 Скачать руководство пользователя страница 96

Страница: 96 / 102

P/N 240011775 Rev. A [02/02/17]

HEAT EXCHANGER CLEANING INSTRUCTIONS

DMG/UCS - 240, 380

FOR UCS & DMG 240/380 BOILERS

WARNING

Fire, explosion, asphyxiation and electrical shock

hazard. Improper installation could result in death or

serious injury. Read this instruction and understand all

requirements, including requirements of authority having

jurisdiction, before beginning installation. Installation

not complete until appliance operation verified per

Installation, Operation & Maintenance Manual provided

with boiler.

Kit installation shall be completed by qualified agency.

Follow instructions TO TURN OFF GAS TO APPLIANCE found

on Operating Instructions label on boiler or in Installation,

Operation & Maintenance Manual. Verify all electrical power

to boiler is turned off.

WARNING

Electrical shock hazard. Turn OFF electrical power supply

at service panel.

Turn power and gas off to the boiler.

Remove screws from front of jacket cover. Lift jacket off

Boiler.

WARNING

Burn hazard. Verify heat exchanger, igniter, and flame

sensor have Burn, Scald hazard. Turn Off water to boiler

Verify unit has cooled before servicing. Use appropriate

personal protection equipment.

Inspect combustion chamber through sight glass. Verify

flame is not present. See Figures 1 and 2.

Allow Boiler to cool.

Press tabs and place control panel in down position. See

Figure 3.

380 - remove four (4) screws securing control support

bracket. Place control securely aside, within boiler cabinet.

See Figure 4.

Disconnect hose to top of condensate trap drain inside

boiler. Place a recepticle (ie: cup, bucket) under hose to

collect debris and cleaning fluid. See Figure 5.

CAUTION

Laceration, burn hazard. Metal edges and parts may

have sharp edges and/or may be hot. Use appropriate

personal protection equipment to include safety glasses

and gloves when installing or servicing this boiler. Failure

to follow these instructions could result in minor or

moderate injury.

WARNING

Combustion chamber insulation in this product

contains ceramic fiber material. Ceramic fibers can

be converted to cristobalite in very high temperature

applications. The International Agency for Research

on Cancer (IARC) has concluded, Crystalline silica

inhaled in the form of quartz or cristobalite from

occupational sources is carcinogenic to humans

(Group1). Avoid breathing dust and contact with

skin and eyes. Use NIOSH certified dust respirator

(N95). This type of respirator is based on the OSHA

requirements for cristobalite at the time this document

was written. Other types of respirators may be

needed depending on the job site conditions. Current

NIOSH recommendations can be found on the NIOSH

website athttp://www.cdc.gov/niosh/homepage.html.

NIOSH approved respirators, manufacturers, and

phone numbers are also listed on this website. Wear

long-sleeved, loose fitting clothing, gloves, and eye

protection. Apply enough water to the combustion

chamber lining to prevent dust. Wash potentially

contaminated clothes separately from other clothing.

Rinse clothes washer thoroughly.

NIOSH stated First Aid. Eye: Irrigate immediately.

Breathing: Fresh air.

Ignition Flame

Detection Electrode

Spark Generator

Sight Glass

Figure 1 - 240 Heat Exchanger - Front of Boiler

Heat Exchanger 240

Auxiliary Control Box

Control

Illustrations are a depiction of boiler for general location of parts and are subject to

change without notice.

Содержание UCS-380







































































































Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды

UTICA BOILERS UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды