UTICA BOILERS UCS-380 Скачать руководство пользователя страница 63

Страница: 63 / 102

9 - START UP PROCEDURE

9.18 Return To The Factory Settings:

• Press the two Menu buttons

simultaneously and

then (+) button until

symbol flashes on the menu

bar.

• Select the INSTALLER menu using

. "COdE"

appears on the display.

• Use (-) or (+) button to input the installer code

0012

•

Confirm using

button. P:1 is displayed with 1

flashing.

• Press the [+] button several times p:df is displayed

with df

flashing.

• Press

button df:x

is displayed with x flashing.

This is the current value of X for dF. Check this against

the value of X on the type plate.

• Enter the value of X shown on the type plate using the

[-] or [+] button.

•

Confirm the value with the

button, df:y is

displayed with y flashing. This is the current value of

for dU. Verify the value of y on the rating plate is the

same.

• Enter the value of y shown on the rating plate using the

[-] or [+] button.

•

Confirm value with the

button. The factory

settings are reset.

• Display returns to current operating mode.

...x

dF =1 dU =1

PN 240011662 Rev. K [01/31/2020]

Содержание UCS-380







































































































Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды

UTICA BOILERS UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UCS-380

Отзывы:

Бренды по названию

Популярные бренды