manualshive.com logo in svg

Utax P-4531DN, Руководство по эксплуатации


Поделиться
Скачать
background image

Operation Panel 

4-76

Default Gateway (Gateway setting)

Specify the default gateway of TCP/IP (IPv6).

1

In the 

Manual Settings

 menu, press 

 or 

 to select 

Default 

Gateway

.

2

Press 

[OK]

. The 

Default Gateway

 screen appears.

3

Use the numeric keys to set the default gateway. 

You can set any value between 0000 and FFFF.
Use 

 and 

 to move the position being entered, which is shown 

highlighted.

4

Press 

[OK]

. The default gateway is stored and the 

Manual 

Settings

 menu reappears.

RA (Stateless) (RA (Stateless) setting)

The IPv6 router communicates (transmits) information such as the global address prefix using ICMPv6. This information is 
the Router Advertisement (RA).

ICMPv6 stands for Internet Control Message Protocol, and is an IPv6 standard defined in the RFC 2463 "Internet Control 
Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification".

1

In the 

IPv6 Setting

 menu, press 

 or 

 to select 

RA(Stateless)

.

2

Press 

[OK]

. The 

RA(Stateless)

 menu screen appears.

3

Press 

 or 

 to select 

RA(Stateless)

.

4

Press 

[OK]

. The 

RA(Stateless)

 screen appears.

5

Press 

 or 

 to select whether RA (Stateless) is enabled.

6

Press 

[OK]

. The RA (Stateless) setting is set and the 

IPv6 Setting

 

menu reappears.

Note  

Before you enter the gateway, be sure to set the 

RA(Stateless)

 setting to 

Off

.

Default Gateway

  1123 : 1451 : 1167 : 

1189

 :1123 : 1451  :1167 : 1189

RA(Stateless):

RA(Stateless)

01

RA(Stateless):

Off

01

On

02

*

Note  

When 

On

 is set, IP addresses are shown in "IP 

Address 1 (to 5)" after network restart.

Содержание P-4531DN

































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P-4531DN

Canon MultiPASS L6000 User Manual preview
MultiPASS L6000
Бренд: Canon Страницы: 251
Canon MultiPASS C5500 Quick Start Manual preview
MultiPASS C5500
Бренд: Canon Страницы: 24
Canon MultiPASS L6000 Quick Start Manual preview
MultiPASS L6000
Бренд: Canon Страницы: 24
Canon Laser Class 700 Series Reference Manual preview
Laser Class 700 Series
Бренд: Canon Страницы: 221
NCR 7150 Quick Start Manual preview
7150
Бренд: NCR Страницы: 2
F+D Feinwerk- und Drucktechnik Plus Software Manual preview
Plus
Бренд: F+D Feinwerk- und Drucktechnik Страницы: 41
QMS Magicolor 6100 Supplementary Manual preview
Magicolor 6100
Бренд: QMS Страницы: 2
Lexmark S510 Series Quick Reference Manual preview
S510 Series
Бренд: Lexmark Страницы: 59
Canon PIXMA TR4500 Series Getting Started preview
PIXMA TR4500 Series
Бренд: Canon Страницы: 100
Konica Minolta Bizhub 4020 Shortcut Manual preview
Bizhub 4020
Бренд: Konica Minolta Страницы: 40
Xerox DocuColor 242 Manual preview
DocuColor 242
Бренд: Xerox Страницы: 128
XYZ Printing da Vinci Jr. 1.0 Instructions preview
da Vinci Jr. 1.0
Бренд: XYZ Printing Страницы: 3
Creality HALOT-ONE PRO User Manual preview
HALOT-ONE PRO
Бренд: Creality Страницы: 24
Oki MB451wMFP User Manual preview
MB451wMFP
Бренд: Oki Страницы: 198
SEWOO LK-T200 User Manual preview
LK-T200
Бренд: SEWOO Страницы: 13
Kuhling&Kuhling RepRap Industrial Operating Manual preview
RepRap Industrial
Бренд: Kuhling&Kuhling Страницы: 24
Citizen CT-S251 User Manual preview
CT-S251
Бренд: Citizen Страницы: 255
Xerox DocuColor 240 Settings Manual preview
DocuColor 240
Бренд: Xerox Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды