USAutomatic STAR I Скачать руководство пользователя страница 8

Страница: 8 / 35

-6

6”

Dimensions from Hinge Pivot Point

Gate Open Direction

STEP 1 Hinge Mount Tube Installation (Part 1)

PULL TO OPEN / TOP VIEW

(SEE BOTTOM OF PAGE FOR PUSH TO OPEN)

(Left-handed installation shown. Reverse for right-handed installation)

STEP 1

Hinge Mount Tube Installation (Part 2)

PUSH TO OPEN / TOP VIEW

(SEE TOP OF PAGE FOR PULL TO OPEN)

(Left-handed installation shown. Reverse for right-handed installation)

Regardless of method used, the hinge mount tube should be very secure since the entire force of the gate is directed to this
mount. The post must be of adequate strength to resist twisting as well.

Conform to dimensions shown at top of page in all cases. See page 7 to locate height of hinge mount tube on post.

Note: USAutomatic is not responsible for failure to comply with UL325 standards, local

building codes or improper installations.

Optional masonry column

Concrete fill recommended.

Dimensions from hinge pivot point

Steel post 4 inch

GATE

minimum

diameter

¼ inch thick wall min.

8 inches

inches

Hinge Mount Tube

Gate Open Direction

(cut as necessary to achieve

dimensions

shown)

Figure

8”

Other Typical Methods for

Pull to Open Applications

Push to Open Applications

Wood post add metal plate and

bolt on with ½ inch carriage

bolt/washers/nuts.

Thin

wall

Round Post

post add

Hinge mount tube

saddle cut

support

must be level

Level

tube for fit

prevent

In all directions for proper

twisting.

alignment and operation.

Figure 1B

Hinge Mount Tube (Cut as necessary to
Achieve dimensions shown)

Steel Post
4” minimum
diameter
¼” min. wall
diameter

Figure 1C

Содержание STAR I




































Результаты поиска

Содержание STAR I

Отзывы:

Похожие инструкции для STAR I

Бренды по названию

Популярные бренды

USAutomatic STAR I, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STAR I

Отзывы:

Похожие инструкции для STAR I

Бренды по названию

Популярные бренды