USAutomatic STAR I Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 35

background image

-11

-

STEP 6

Installation of Charging Source

SOLAR PANEL

Locate and mount the solar panel bracket so that the panel faces southwest and maintains the preformed 45-
degree angle. The standard cable is 10' in length and must feed in through the bottom of the control box. Pay
attention to the distance when determining you’re mounting location. Although the cable can be extended with
watertight connectors, charging power is diminished. Sometimes it is necessary to locate the panel farther away
to achieve optimum sunlight, but consider that optimum sunlight might not mean optimum charging if the
distance is to great. Use #16 gauge wire or larger and keep length as short as possible.

STAR

Assemble panel(s) to bracket
with supplied hardware.

Panel facing

s

outhwest.

NOTE: Avoid shaded areas if possible. Panels should face southwest for optimum

charging. See explanation above for details.

AC CHARGER

Locate and install the AC battery charger inside the control box. The charger requires a receptacle for 110-volt
AC supply; recommended location is inside the control box. A licensed electrician per local building codes
should

install

the

receptacle.

Note:

USAutomatic recommends an AC surge protector on all 110-volt installations.

Especially

in lightning prone areas.

STEP 7 Installing Safety Placards

Mount safety placards on gate. Two signs are provided. Place one sign on each side of the gate where it will be
highly visible to anyone on either side of the gate.

STEP 8 Installing Secondary Entrapment Siren

The secondary entrapment siren connects to the control board (see page 33). This siren is very loud and will be
activated anytime the current sense circuit stops the gate twice prior to reaching a fully open or close limit. The
reset button on the control board (see page 13) must be pushed to turn off the siren, and reset the control board.

Deep cycle

Battery

Red wire +

Black wire -

Do not connect battery wires from actuator/control board at this time.

Control

Receiver

Board

+

Battery

Charger

Junction box mounted inside control box.

Conduit

-

«
...
11
12
13
14
15
...
»

Содержание STAR I




































Отзывы:

Нет отзывов

Похожие инструкции для STAR I

LiftMaster Security+ 1210EM FS2

Бренд: Chamberlain Страницы: 80

Бренд: Salton Страницы: 21

Бренд: Tymetal Corp. Страницы: 38

Бренд: Rosle Страницы: 32

Бренд: Grants Automation Страницы: 9

Бренд: Tecno Automazione Страницы: 2

STARCUS K06/K10

Бренд: krispol Страницы: 24

Бренд: CAME Страницы: 64

Бренд: FAAC Страницы: 11

Бренд: Beninca Страницы: 24

Бренд: Hamilton Beach Страницы: 12

Open Ease 76300R

Бренд: Hamilton Beach Страницы: 10

Бренд: Hamilton Beach Страницы: 2

COMMANDER 2000RGD

Бренд: Raynor Страницы: 72

Бренд: CAME Страницы: 26

Бренд: Entrematic Страницы: 4

Бренд: GATEXPERT Страницы: 31

Бренд: FAAC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды