USA Measurements US-4011 Скачать руководство пользователя

Страница: 4 / 42

US-4011

INTRODUCTION

This manual contains installation, operation and maintenance instructions for the US-4011 indicators. Please read this

manual completely before installation and operation.

1.1.

Safety Precautions

For safe and dependable operation of this equipment, please comply with the following safety precautions:

Verify that the input voltage range printed on the data label matches the local AC power to be used.

Make sure that the power cord does not pose a potential obstacle or tripping hazard.

Use only approved accessories and peripherals.

Operate the equipment only under ambient conditions specified in these instructions.

Disconnect the equipment from the power supply when cleaning.

Do not operate the equipment in hazardous or unstable environments.

Do not immerse the equipment in water or other liquids.

Service should only be performed by authorized personnel.

NOTE:

Some functions maybe disabled by manufacture before shipping, if you need these functions or don’t want to

use some other functions, please contact with manufacture in advance, because of this, some operations or faceplate
maybe are a little bit different, and some description sections may be deleted.

1.2.

Specification

Model

US-4011

Max Display Range

-999,999 to 999,999

Max Display Resolution

1:100,000 (primary unit)

1:125,000 (second unit)

Max Approved Resolution

1/5000 (NTEP/MC), 1/3000 (OIML)

Division

0.0001,0.0002,0.0005------10,20,50

Calibration Unit

kg or lb

Weighing Unit

kg, lb, lb:oz, g, oz, pcs, %

Display

6-digit, 7-segment, 1" (25mm) LCD with blue backlight

Accuracy

≤

0.01%

Power supply

Alkaline Batteries: 4 x “AA” size cells

AC Adapter: 6Vdc/500mA, with central positive
USB

Work current

≤

15mA (with backlight off, no load cells)

≤

30mA (with backlight on, no load cells)

≤

50mA (with backlight on and one 350 load cell)

Functions

Normal weighing, Counting, Percent weighing, Check weighing, BMI, Hold, Accumulation

Zero Range

Programmable zero range

Tare Range

Full capacity

Stabilization Time

<3 seconds

Содержание US-4011











































Результаты поиска

Содержание US-4011

Отзывы:

Похожие инструкции для US-4011

Бренды по названию

Популярные бренды

USA Measurements US-4011, Руководство пользователя и техническое руководство

Результаты поиска

Содержание US-4011

Отзывы:

Похожие инструкции для US-4011

Бренды по названию

Популярные бренды