US-4011
.
21
.
be used next time.
5.3.6.
Check Percent (percentage compare) in Percent weighing mode:
(1)
To make percentage compare function be available,
CONFIG-FUNC-COMPAR
menu item should set to
YES
, and
high and low limitation of percentage should be set correctly according to following steps:
(2)
In percent weighing mode, Press down
UNIT/DATA
key more than 3s to input compare data of high and low.
(3)
After
HIGH
being shown,
000000
will be displayed, use
keys to input high percentage number and
press
TARE/PRESET
key to confirm. Announciator of
Hi
will be shown in this step. Press
ZERO/ON/OFF
key to exit
and back to percent weighing mode.
(4)
After
Low
being shown,
000000
will be displayed, use
keys to input low percentage number and press
TARE/PRESET
key to confirm. Announciator of
Lo
will be shown in this step. Press
ZERO/ON/OFF
key to exit and
back to counting mode.
NOTE:
If High number is 0 or is equal or less than low number, the comparison will be disabled.
(5)
After a reasonable limitation is set and compare is be active, one of announciators
HI, OK, LO
will be lighted, and
the beeper will sound according to its setting in
USER-BEEP
.
5.4.
BMI Working Mode (CLOSED):
5.4.1.
To make BMI working Mode be available,
CONFIG-FUNC-BMI
menu item should be set to
YES
and factory setting
should be also enable this function.
5.4.2.
To enter BMI Working mode:
5.4.2.1.
When
CONFIG-FUNC-ACCUMU
=
Yes
:
If In normal weighing mode, percent weighing mode, or counting mode,
long press
PRINT/FUNC
key, one of
WEIGH
or
COUNT
or
PERCEN
will be shown, use
ACC/TOTAL
or
PRINT/FUNC
key to select
BMI
, then press
TARE/PRESET
to confirm go to BMI mode.
5.4.2.2.
When
CONFIG-FUNC-ACCUMU
=
NO
:
press
ACC/TOTAL
(
BMI
) key, go to BMI mode.
5.4.3.
After scale go to this mode, “
CM
.xxx” (means: last input height is xxx cm) or “
IN
.xx.x” (means: last input height
is xx.x inch) will be displayed, and to wait for input height: (1)to change height unit to cm or inch by pressing
UNIT/DATA
key; (2) to change height number by using
PRINT/FUNC, ACC/TOTAL(BMI)
keys; (3)Press and hold
down
PRINT/FUNC
or
ACC/TOTAL(BMI)
key will increase or decrease number fast, (4) Press
TARE/PRESET
key
to confirm the input. Press
ZERO/ON/OFF
key to exit input data mode and back to BMI working mode. The range
of height is 50-250cm(19.7-98.4inch) and default is 170cm(66.9inch)
5.4.4.
In this mode, when BMI number is shown (BMI announciator is on also), or weight number is shown (BMI and kg
or lb announciators are on), Press
ACC/TOTAL
key to select weight or BMI number to be displayed, when weight
is displayed, the weight unit can be selected by pressing
UNIT/DATA
key, and BMI and weight unit will be
displayed at same time.
5.4.5.
In this mode, when current net weight is less than
NLD.RNG
, the indicator will go to display weight number
if
CONFIG-FUNC-ACCUMU
=
No
; or the indicator will back to original working mode if
CONFIG-FUNC-ACCUMU
=
Yes
.
5.5.
HOLD Function:
5.5.1.
HOLD
function can be used to freeze display number. In this mode, scale can catch a dynamic number, hold a
stable number, or average a unstable number, then HOLD(freeze) this number temporary for user to watch or
record. This function can be used in normal weighing mode, counting mode and percent weighing mode. The
speed of A/D converter is increased to 80Hz (if
CONFIG-AD.H.SPD
is set to
YES
) from original 10Hz for some
Содержание US-4011
Страница 1: ...US 4011 Indicator User Technical Manual Contents subject to change without notice Version 1 0 ...
Страница 2: ...US 4011 1 07 2017 ...
Страница 7: ...US 4011 4 3 OVERVIEW OF CONTROLS AND FUNCTIONS 3 1 Indicator Display Character Definitions ...
Страница 30: ...US 4011 27 TABLE6 1 Location Code for different elevation and latitude ...
