USA Measurements US-4011, Руководство пользователя и техническое руководство

Страница: 23 / 42

US-4011 .
20 .
5.3. Percent Weighing Mode:
5.3.1. In this mode, scale will weigh goods weight on it, calculate and display its percentage after the
unit-percentage-weight of goods is obtained. (NOTE: If
100% display format is set to 100%, 100.0% or
100.00% in
CONFIG-FUNC-PERCEN
menu item, then, the unit-percentage-weight is the weight of 1%, 0.1% or
0.01% )
5.3.2. To make percent weighing function be available,
CONFIG-FUNC-PERCEN
menu item shouldn’t be set to
NO
.
5.3.3. To enter percent weighing mode, in normal weighing or counting mode, long press PRINT/FUNC key,
WEIGH
or
COUNT
or
BMI
will be shown, use ACC/TOTAL or PRINT/FUNC key to select
PERCEN
, then press TARE/PRESET to
confirm go to percent weighing mode. Before new unit-percentage-weight is got, the last unit-percentage-weight
will be used.
5.3.4. In percent weighing mode, the function of ZERO, ON/OFF, TARE, PRESET TARE, ACC, PRINT, HOLD, SETUP are
available.
5.3.5. To obtain the unit-percentage-weight, there’re two ways :
(1) Input weight and its percentage, then scale calculates the unit-percentage-weight, refer operations of
step5.3.5.1
(2) Weigh samples weight which percentage is known, refer operation of step5.3.5.2
5.3.5.1 Input weight and its percentage from keypad, and calculate unit-percentage-weight: in percent weighing mode,
press UNIT/DATA key, When
InP.Pct
is shown, press TARE/PRESET key to enter this mode:
a. Before input weight, use PRINT/FUNC or ACC/TOTAL key to select the percentage from 1%, 2%, 5%, 10%,
20%, 50% and 100%, this percentage is corresponding to the weight you will input in following steps
b. When
UNIT.KG
is shown, use PRINT/FUNC or ACC/TOTAL key to select the unit of input weight, use
TARE/PRESET key to confirm and go to next. Press ZERO/ON/OFF key to exit and back to percent weighing
mode.
c. When last stored unit-percentage-weight data is shown, use keys to input new unit-percentage
-weight, press SETUP key more than 3s to input decimal point. Press TARE/PRESET key to confirm and save it,
then go back to percent weighing mode. If the calculated unit-percentage-weight is less than 0.5d, the
indicator will display
Pct.Er
and go back to percent weighing mode.
5.3.5.2 Obtain unit-percentage-weight by weighing samples weight which percentage is known: in percent weighing
mode, press UNIT/DATA key, When
InP.Pct
is shown, use PRINT/FUNC or ACC/TOTAL key to select
SPL.Pct
,
press TARE/PRESET key to weigh samples (which percentage is known) weight, calculate piece weight. Press
Z E R O / O N / O F F k e y t o e x i t a n d b a c k t o p e r c e n t w e i g h i n g m o d e .
a. When
SPL.Lo
is shown, move away any sample on scale and press TARE/PRESET key to confirm, before scale is
stable,
SPL.Lo
will be flashed. After it is stable, it will go to next step. Press ZERO/ON/OFF key to exit and back
to percent weighing mode.
b. When
SPL.Hi
is shown, put samples (its percentage is known) onto the scale, Press TARE/PRESET key to
confirm reading weight. Before scale is stable,
SPL.Hi
will be flashed. After it is stable, it will go to next step.
Press ZERO/ON/OFF key to exit and back to percent weighing mode.
c. After
INP.PCT
being shown,
000000
(position of decimal point is determined by
CONFIG-FUNC -PERCEN
setting)
will be displayed, use keys to input the percentage of samples and Press TARE/PRESET key to
confirm. If the calculated unit-percentage-weight is less than 0.5d, the indicator will display
Pct.Er
and go back
to percent weighing mode, otherwise, after the reasonable unit-percentage-weight being got, the scale will go
back to percent weighing mode. The gotten unit-percentage-weight can be saved after the power off and can