US-4011
.
18
.
5.1.8.
Check Weight in weighing mode:
(1)
To make weight compare function be available,
CONFIG-FUNC-COMPAR
item should set to
YES
, and high and low
limitation of weight should be set correctly according to following steps:
(2)
In weighing mode, Press down
UNIT/DATA
key more than 3s to input compare data of high and low. When
UNIT.KG
is shown, use
PRINT/FUNC
or
ACC/TOTAL
key to select the unit of weight, use
TARE/PRESET
key to confirm and go
to next. Press
ZERO/ON/OFF
key to exit and back to weighing mode.
(3)
After
HIGH
being shown,
000000
will be displayed, use
keys to input high weight number and press
TARE/PRESET
key to confirm. Announciator of
Hi
will be shown in this step. Press
ZERO/ON/OFF
key to exit and
back to weighing mode.
(4)
After
Low
being shown,
000000
will be displayed, use
keys to input low weight number and press
TARE/PRESET
key to confirm. Announciator of
Lo
will be shown in this step. Press
ZERO/ON/OFF
key to exit and
back to weighing mode.
NOTE:
If High number is 0 or is equal or less than low number, the comparison will be disabled, and the input data
has no limitation.
(5)
After a reasonable limitation is set and compare is be active, one of announciators
HI
,
OK
,
LO
will be lighted, and
the beeper will sound according to its setting in
USER-BEEP
.
5.1.9.
Accumulation:
Press
ACC/TOTAL
key to add displayed number to accumulation memories, and accumulation times will also add up 1.
And then to display accumulation result.
5.1.10.
Output data:
When reading is stable, press
PRINT/FUNC
key.
5.1.11.
Change working mode:
Long press
PRINT/FUNC
key, then use
keys to choose and confirm to enter into weighing mode,
counting mode , percentage working mode or BMI working mode.
5.1.12.
Enter to or exit from HOLD mode:
Press
SETUP
key.
5.1.13.
Enter Setup Mode:
(1)
If need to set configuration parameters, set user parameters, calibrate the scale, set current date or time, test
some hardware… It’s need to long press
SETUP
key to enter setup mode
(2)
After Entering Setup Mode, the main menu item
CONFIG
will be shown first.
(3)
In Setup mode, use
keys to select wanted submenu and wanted menu item, select
wanted choice, set wanted number, confirm and save data, or exit this mode. Please refer the
“4.Operation Menu
Structure”
.
5.2.
Count Weighing Mode:
5.2.1.
In this mode, scale will weigh goods weight on scale, calculate and display its counts after the piece weight of
goods is obtained.
5.2.2.
To make counting function be available,
CONFIG-FUNC-COUNT
item should be set to
YES
in
CONFIG
menu.
5.2.3.
To enter counting working mode, in normal weighing or percent-weighing mode, long press
PRINT/FUNC
key,
WEIGH
or
PERCEN
or
BMI
will be shown, use
ACC/TOTAL
or
PRINT/FUNC
key to select
COUNT
, then press
TARE/PRESET
key to confirm go to parts counting mode. Before new piece weight is got, the last piece weight
will be used.
5.2.4.
In counting working mode, the function of
ZERO, ON/OFF, TARE, PRESET TARE, ACC, PRINT, HOLD, SETUP
are
Содержание US-4011
Страница 1: ...US 4011 Indicator User Technical Manual Contents subject to change without notice Version 1 0 ...
Страница 2: ...US 4011 1 07 2017 ...
Страница 7: ...US 4011 4 3 OVERVIEW OF CONTROLS AND FUNCTIONS 3 1 Indicator Display Character Definitions ...
Страница 30: ...US 4011 27 TABLE6 1 Location Code for different elevation and latitude ...
