manualshive.com logo in svg

Urrea CE1115, Руководство пользователя и гарантия, Страница: 23 / 44

Поделиться
Скачать
Urrea CE1115 Скачать руководство пользователя страница 23

23

E N G L I S H •

User’s manual

EXTENSION CORDS

 WARNING: To reduce the risk of fire or elec-

trical shock, use the proper gauge of extension 
cord. When using an extension cord, be sure 
to use one heavy enough to carry the current 
your machine will draw.
The smaller the gauge-number, the larger the 
diameter of the extension cord is. If in doubt 
of the proper size of an extension cord, use a 
shorter and thicker cord. An undersized cord 
will cause a drop in line voltage resulting in a 
loss of power and overheating.

 CAUTION: USE ONLY a 3-wire extension 

cord that has a 3-prong grounding plug and 
a 3-pole receptacle that accepts the machine’s 
plug.

PERSONAL SAFETY

Stay alert, watch what you are doing and use 
common sense when operating a power tool. 
Don’t use the tool if you are tired or under the 
influence of drugs, alcohol or medication. A 
moment of inattention while operating power 
tools may cause a serious personal injury.
Dress properly. Do not wear loose clothing 
or jewelry. Contain long hair. Keep your hair, 
clothing and gloves away of moving parts. 
Loose clothes, jewelry or long hair can be 
caught in moving parts.
Avoid an accidental starting. Be sure that the 
switch is OFF before plugging in. Carrying 
tools with the finger on the switch or plug in 
the tool switch in ON may cause accidents.
Remove the adjusting keys or wrenches be-
fore turning the tool on. A wrench or a key 
that is left close to a rotating part of the tool 
may provoke a personal injury.
Do not overreach. Keep proper footing and 
balance at all times. Proper footing and bal-
ance enables better control of the tools on un-
expected situations.
Use safety equipment. Always wear eye pro-
tection. Dust mask, nonskid safety shoes, hard 
hat, or hearing protection must be used for ap-
propriate conditions.
Before connecting the tool to a power source 
(receptacle, outlet, etc.) be sure that the volt-
age supplied is the same as that one specified 
on the nameplate of the tool. To use a not 
specified voltage may cause a serious injury to 
the user as well as damage the tool.

 IMPORTANT: This appliance is not intended 

for use by persons (including children) with re-
duced physical, sensory or mental capabilities 
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by 
a person responsible for their safety. Children 
should be supervised to ensure they do not use 
the devices as toys.

TOOL USE AND CARE

Do not force the power tool. Use the correct 
tool for the application. The correct tool will 
do the job better and more safely at the rate 
that it was designed to work at.
Do not use tools if switch does not turn it on 
or off. Any tool that cannot be controlled with 
the switch is dangerous and must be repaired.
Disconnect the plug from the power source 
before making any adjustments, changing ac-
cessories or storing the tool. This preventive 
safety measures reduce the risk of accidental 
starting of the tool.
When the power tool is not in use, store it out 
of the reach of children, and do not allow in-
dividuals who are not familiar with the power 
tool or these instructions to operate it. Power 
tools are dangerous in the hands on untrained 
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts, 
and any other condition that may affect the 
operation of the power tool. If it is damaged, 
have it repaired before using. Many accidents 
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving 
parts, breakage parts, and any other condition 
that may affect the tools operation. If you find 
a damaged tool, take it to service before use it. 
Use only accessories that are recommended by 
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous 
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened 
edges, are less likely to stuck in workpieces or 
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and differential switch 
when you are using an electric equipment.

 

   

   

Содержание CE1115













































Отзывы:

Нет отзывов