20
DS1332-107B
21
DS1332-107B
2.6 OPENING OF AN EXTERNAL DOOR WITHOUT DOOR PHONE CALL
To activate the door opening command (relay ATT1 or ATT2) in standby mode, enter the following
codes:
MODE
BCA MODE
COMBIPHONE MODE
ATT1 activation without door phone call
# # 1
R35
ATT2 activation without door phone call
# # 2
R37
2.7 OPENING OF AN EXTERNAL DOOR DURING A CONVERSATION
To open an external door during a conversation (external or door phone conversation):
MODE
BCA MODE
COMBIPHONE MODE
ATT1 automatic opening after door phone call
1
# # 1
R35
ATT2 automatic opening after door phone call
2
# # 1
R35
ATT1 activation after door phone call 2
# # 8
R38
ATT2 activation after door phone call 1
# # 2
R37
The selected relay will be activated and a con
fi
rmation tone will be heard in the handset; then the conversation
on the line in hold mode will become active again. If the door is opened after a call coming from the door
phone, it is not necessary to enter the door number, the system will automatically open the door from which
the call is coming, entering a single code (
# # 1
or
R35
, according to settings). After the con
fi
rmation tone,
the conversation in progress automatically is resumed.
3.0 INTERFACE SERVICES PROGRAMMING
PROGRAMMING PROCEDURE
To perform all the programming procedures, regardless of the interface operating mode (mode A or mode
B), follow the instructions below:
1. Pick the handset up and wait for 20 seconds, until the telephone is disabled.
2. For
the
fi
rst 10 seconds will be heard the dialling tone, for the next 10 seconds the alert tone and then
the silence.
3. Enter
* # # *
.
4. The interface will answer with a con
fi
rmation tone, to indicate the access to the programming mode.
5. Enter the two digits of the parameter to be programmed (from 01 to 10) and con
fi
rm it by pressing
*
.
6. Enter the value of the parameter to be programmed and close the programming procedure by entering
#
.
7. The interface con
fi
rms the successful programming operation with a tone; if the value is wrong, the
interface emits the alert tone.
8. After performing a programming operation it is possible to perform another one, starting by step 5.
9. To close the programming procedure, hang the handset up. Only the parameters con
fi
rmed by pressing
#
will be stored.
All the programmed parameters will be stored in a non volatile memory and keep the programmed value
also in case of mains fail.
In the following cases will be emitted an error tone for 3 seconds:
Error during parameter input.
Error during value input.
Wrong dialling during programming procedure.
Fail during data storage.
§
•
•
•
•
Programming example:
It is needed to program the closing time of the ATT1 actuator relay contact and set it to 10 seconds. The
parameter of the actuator relay 1 is 03 and the value used for 10 seconds is 4. The programming sequence
will be the following:
Pick the handset up, wait for 20 seconds (until no tone in the handset) and enter:
* # # * 03 * 4 #
After the con
fi
rmation tone, hang the handset up.
3.1 CODE FOR PARAMETERS RESET
In order to perform a complete reset of the parameters and set them to factory values for Italian version
(parameter 08 value 1 of the summarizing table), pick the handset up and enter the RESET code.
* * * # # # * #
3.2 DTMF CODE PROGRAMMING FOR TRUNK LINE ENGAGEMENT
It is possible to program the code to be entered to access the trunk line, when the interface operates in
mode
B
. After entering in the programming procedure following the previously described steps, enter the
number of parameter 01 and the desired value, according to the table below. By default, is set the value 1,
i.e. engagement with digit 0.
Parameter
01
Value
1
2
DTMF command for engagement
0
9
When the interface is programmed in mode
A
, remember that the trunk line is directly present on the
connected telephones, without entering any code.
3.3 TELEPHONE TYPE PROGRAMMING: COMBIPHONE OR BCA
It is possible to select the telephone type used in the system. Select between:
BCA telephone (a common telephone with DTMF dialling)
Combiphone or Director2 telephone: with these telephones will be available some buttons for simpli
fi
ed
functions.
After entering in the programming procedure following the previously described steps, enter the number
of parameter 02 and the desired value, according to the table below. By default, is set the value 1, i.e.
Combiphone.
Parameter
02
Value
1
2
Telephone type
Combiphone
BCA
Remember that, regardless of the selected mode (BCA or COMBIPHONE), telephones must be set for
DTMF dialling.
3.4 PROGRAMMING PROCEDURE OF ATT1 RELAY ACTIVATION TIME
It is possible to program activation times of the ATT1 actuator relay. After entering in the programming
procedure following the previously described steps, enter the number of parameter 03 and the desired
value, according to the table below. By default, is set the value 1, i.e. 1 second.
Parameter
03
Value
1
2
3
4
Activation type
1 s
2 s
4 s
10 s
•
•
§
•
•
§
