URC MRX-10 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 11

background image

69

RS-232 Connection

The MRX-10 can operate equipment via RS-232 communication. This allows discrete serial commands
to be triggered from a Total Control remote and sent from the MRX-10 over the network connection.
The signal is then sent to the device over proprietary URC RS-232 cables. These use either male or
female DB-9 connections with standard pin-outs. Programming is done in the Accelerator software.

«
...
5
6
7
8
9
...
»

Содержание MRX-10












Отзывы:

Нет отзывов

Похожие инструкции для MRX-10

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Бренд: Uniden Страницы: 28

Бренд: UniFocus Страницы: 23

Бренд: UniFocus Страницы: 6

Бренд: Valcom Страницы: 6

Бренд: Audioaccess Страницы: 2

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

Бренд: Greenheck Страницы: 4

Бренд: Vector Страницы: 8

ibaMS16-DI-220V Series

Бренд: IBA Страницы: 32

Smart 4 Universal

Бренд: Classic Страницы: 12

Бренд: Pilz Страницы: 9

Бренд: HEIDENHAIN Страницы: 32

XBee DigiMesh 2.4

Бренд: Digi Страницы: 157

Бренд: Instrutech Страницы: 42

Бренд: FUHR Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды