UPlay Today ABT-DXBN-N Скачать руководство пользователя страница 52

Страница: 52 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

STEP 21 - CONNECT SECOND DECK TO UPRIGHTS

4th post
removed
for clarity

1. Stand (4) 11ft Uprights(A) into position
with clamp flange pointing inward.

2. Lift Deck(B) and positon onto clamp flange
of (4) 11ft Uprights(A).

3. Align hole in clamp flange with slot on
underside of Deck(B).

See Figure 1

4. Insert Bolt(C) and Flat Washer(D) upward
into hole in Clamp and through slot in Deck(B).
While pushing upright tightly against Deck(B),
secure with Flat Washer(D) and Lock Nut(E).

5. Repeat Steps 3 and 4 for remaining Uprights(A).
Tighten all hardware.

6. Check levelness of deck and make the
appropriate adjustments.

Clamp

Flange

Figure 1

Parts List

Letter Description

Quantity Part Number

Uprights w/clamp

02-07-0001
02-07-0003

33-12-0019
33-11-0004
33-11-0200
33-11-0400

36-3/4” (933mm) Deck

Hardware Complete

M10 x 30 BHCS Bolt

M10 Flat Washer

M10 Lock Nut

Assemble deck and uprights
close to their installed
position.

Coating on deck may prevent insertion
of hardware. Trim out slots with utility
knife if necessary.

Posts must be supported until
all hardware is installed.

Содержание ABT-DXBN-N


















































































Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды

UPlay Today ABT-DXBN-N, Руководство по сборке

Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды