UPlay Today ABT-DXBN-N Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 81

background image

14

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

WARNING LABEL APPLICATION INSTRUCTIONS

The enclosed Warning Labels must be af

ﬁ

xed to your playground equipment. At least

one Warning Label is needed per play structure, permanently af

ﬁ

xed in a conspicuous

location within easy view of users.

INSTRUCTIONS:

1. Fully assemble and install your UPlay Today™ playground equipment per the accom-
panying installation instructions.

2. When installation of the equipment is complete, and prior to allowing use of the
equipment, identify a suitable location on the structure to receive the Warning Label. An
upright post is recommended, approximately 4 feet above the ground. Choose an up-
right post most likely to be seen by the user immediately upon entry into the play area.

3. Fully clean the surface to receive the label with soap and water, and ensure that no
oils,

ﬁ

lm, or dirt remain.

4. Allow surface to dry fully. Apply the Warning Label, smoothing over the surface with a
clean cloth so there are no air bubbles present.

5. For larger structures (more than 16 upright posts), use 2 labels, positioning one at
each end of the structure. Always choose locations, which are likely to be seen by users
prior to use of the equipment, preferably near the entry point of the play area.

ALWAYS FOLLOW THE RECOMMENDATIONS CONTAINED IN THE ACCOMPANYING SAFE-
TY GUIDELINES REGARDING THE INSTALLATION AND MAINTENANCE OF APPROPRIATE
RESILIENT SURFACE MATERIALS REQUIRED FOR YOUR PLAY AREA. NEVER ALLOW USE
OF PLAYGROUND EQUIPMENT WITHOUT PROPER SAFETEY SURFACING AS FALLS ONTO
A HARD SURFACE CAN CAUSE SERIOUS INJURY TO THE USER.

Finally, if you should have any questions regarding the proper installation of this equipment, please
contact UltraPlay at:

UltraPlay Systems
UPlay Today™ Customer Service
1675 Locust Street, Red Bud, IL 62278
1-800-458-5872 Fax 1-618-282-8202
E-mail: [email protected]

«
...
14
15
16
17
18
...
»

Содержание ABT-DXBN-N


















































































Отзывы:

Нет отзывов

Похожие инструкции для ABT-DXBN-N

Бренд: Caddon Hives Страницы: 3

Бренд: Jacto Страницы: 12

Бренд: Frontier Страницы: 16

Бренд: Plum Страницы: 44

Бренд: Daytona Страницы: 8

Бренд: CYKLOP Страницы: 2

i7300 ReverbMaster

Бренд: Phonic Страницы: 37

Бренд: Harman Kardon Страницы: 2

PipeFeeder Dump

Бренд: Hanskamp Страницы: 23

Q-WASH 360Z-LED

Бренд: Chauvet Страницы: 8

Бренд: KAM Страницы: 9

Бренд: NEO Страницы: 16

Бренд: Teagle Страницы: 32

Бренд: DRUCK & TEMPERATUR Leitenberger Страницы: 72

Бренд: Envitec Страницы: 36

Бренд: Rehau Страницы: 4

PAS Vr. Alcohol Screening & Verification System

Бренд: PAS Systems International Страницы: 40

APART Plus DIM 7

Бренд: sobex Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды