UPlay Today ABT-DXBN-N Скачать руководство пользователя страница 19

Страница: 19 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

USE ZONE-CONFIGURATION 1

46’

27’

MINIMUM USE ZONE REQUIRED

TOP VIEW

6’

NOTE: Equipment should be placed to eliminate conflicting traffic patterns.

As a general rule, allow at least 6’ of free space around the entire structure.

IMPORTANT:

Never install play equipment over hard, unresilient

surfaces such as asphalt, concrete or compacted earth. It is the
owner’s responsibility to ensure the “minimum area required”
contains an appropriate amount of resilient material to cushion
accidental falls.

(3)Roofs

(02-07-0037)

(3)Decks

(02-07-0003)

(8) 11’

Uprights

(02-07-0001)

(4) 13’

Uprights

(02-07-0002)

(2) Grab Bars

(02-07-0033)

Slide Hood

(02-07-0025)

Slide Hood

(02-07-0025)

ADA Stairs

(02-07-0005)

Left ADA Handrail

(0207-0008)

Right ADA

Handrail

(0207-0010)

Bongos

(02-07-0014)

Rung Climber

Entry Archway

(02-07-0031)

6’ Wave Slide

(02-07-0028)

Rung Climber

(02-07-0030)

Ship’s Wheel

Panel

(02-07-0016)

ADA Step

(02-07-0006)

ADA

Handhold

(02-07-0011)

ADA Deck

Support Post

(02-07-0047)

ADA Deck

(02-07-0004)

Rain Wheel

(02-07-0012)

Bass Drum

(02-07-0013)

Curved Slide

(02-07-0027)

Window Panel

(02-07-0019)

Bone Bridge

(02-07-0023)

6’

Ultra

Mtn. Climber

(02-07-0034)

Straight Slide

(02-07-0026)

2’ Tower

Stairs

(02-07-0007)

2’ Tower Stair Handrail -Left

(02-07-0009)

2’ Tower Stair Handrail-Right

(02-07-0029)

Slide Hood

(02-07-0025)

Содержание ABT-DXBN-N


















































































Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды

UPlay Today ABT-DXBN-N, Руководство по сборке

Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды